Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 75 / 142

background image

FUNC (K)/Ver. 1.01

Confidential

63

18 DTMF

The transceiver supports DTMF (Dual Tone Multiple
Frequency) as a signaling method.
DTMF uses 2 different tones simultaneously. DTMF can
be used to make a call with a PTT ID or an individual call,
transmit the telephone number while connecting to the
phone line, and remotely control the transceiver.
DTMF signaling uses 2 different frequencies (a high
frequency and a low frequency) and consists of DTMF 0
to 9, A to D, *and # Code.

Table 18-1 DTMF Code Frequency List

18.1 Sending DTMF Code

The following methods can be used to send a DTMF
code:
•

Manual Dialing

•

Store & Send

•

Keypad Auto PTT

•

Autodial List Selection

18.1.1 Manual Dialing

Manual Dialing allows a user to send a DTMF tone
corresponding to a particular key when the

[0]

to

[9]

,

[*]

,

or

[#]

keys on the keypad is pressed while transmitting by

pressing the

PTT

switch.

Manual Dialing can be configured to be enabled or
disabled by using KPG-101D.

Transceiver Operation

1.

Press the

PTT

switch.

2.

Press a key corresponding to the DTMF code to
send.
The transceiver sends the DTMF code.

3.

Repeat the step 2 if necessary.

Configuration using KPG-101D

•

Configuring the Manual Dialing (Refer to FPRG
6.10.1 Encode Tab - Manual Dialing.)

18.1.2 Store & Send

When using Store & Send, the desired series of DTMF
codes can be entered via the keypad but then be sent at
a later time. A maximum of 16 digits can be transmitted
in a single Store & Send operation.
Store & Send can be configured to be enabled or
disabled by using KPG-101D. Select “DTMF (Autodial)”
from the

Keypad Operation

dropdown list unless the

Autodial

key is used.

Transceiver Operation

z

Using the Keypad
1.

Press the

Autodial

key.

The Store & Send Entry display appears on the
display.
Select “DTMF (Autodial)” from the

Key

Assignment

window >

General

tab >

Keypad

Operation

dropdown list unless the

Autodial

key is used.

2.

Enter the DTMF code to send using the
keypad.
The entered code is confirmed.

3.

Repeat step 2 if necessary.

Frequency

1209 Hz

1336 Hz

1447 Hz

1633 Hz

697 Hz

1

2

3

A

770 Hz

4

5

6

B

852 Hz

7

8

9

C

941 Hz

*

0

#

D

«
...
73
74
75
76
77
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

Brand: DAPAudio Pages: 28

Brand: Garmin Pages: 11

Twintalker 7100

Brand: Topcom Pages: 22

Yakumo DVD Travelle

Brand: YAKUMO Pages: 40

Brand: EDIFIER Pages: 6

Brand: LENCO Pages: 39

Brand: Winco Pages: 13

SKYLINE HFP3000

Brand: INE Pages: 96

Brand: Tektronix Pages: 282

Brand: Clas Ohlson Pages: 16

Brand: Intermec Pages: 8

Brand: LENCO Pages: 3

Brand: Noblex Pages: 15

DVP-FX921K - 9" Portable Dvd Player

Brand: Sony Pages: 2

DVP-FX820 - DVD Player - 8

Brand: Sony Pages: 2

Brand: Sony Pages: 3

DVP-FX921 Marketing Specifications (DVP-FX921)

Brand: Sony Pages: 40

Brand: Sony Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands