Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 36 / 142

background image

24

Confidential

FUNC (K)/Ver. 1.01

5 PASSWORD FUNCTION

The transceiver has a password function to protect the
transceiver operation and configuration of data.

5.1 Transceiver Password

This password prevents unauthorized persons from
operating the transceiver. The transceiver activates
normally if the correct password is entered after the
transceiver is turned ON.
The Transceiver Password can be configured by using
KPG-101D. The Transceiver Password can be
configured using any numbers between 0 and 999999.
The Transceiver Password can be entered by using the
keypad,

Selector

or

PF

keys.

Transceiver Operation

z

Using the keypad
1.

Press the numeric keys on the keypad to enter
the password.

2.

Press the

[S]

or

[*]

key after the password is

entered.
The transceiver emits the Password
Authorization Tone if the correct password is
entered.
“PASSWORD” appears on the LCD if an
incorrect password is entered and the
transceiver returns to Password Entry Mode.

z

Using the Selector
1.

Select a character using the

Selector

.

2.

Press the

[C>]

key to confirm the number.

The selected number stops blinking and is
confirmed on the display.

3.

Repeat steps 1 and 2 to enter the entire
password.

4.

Press the

[S]

or

[*]

key after the entire password

is entered.
The transceiver emits the Password
Authorization Tone if the correct password is
entered.
“PASSWORD” appears on the LCD if an
incorrect password is entered and the
transceiver returns to Password Entry Mode.

Note:

The following keys can be used for entering a password.

Table 5-1 Key Operation

Configuration using KPG-101D

•

Configuring the Transceiver Password (Refer to
FPRG 6.7.1 Common Page 1 Tab - Transceiver
Password.)

•

Assigning functions to the

PF

keys (Refer to

FPRG 6.8 Key Assignment.)

Figure 5-1 Transceiver Password Operation

Key

Operation

Selector

Increases or decreases the displayed
number (0 to 9).

Side 1

The “PASSWORD” appears on the
display.

[S]

Password Confirmation

[A]

Press: Deletes a number.
Hold: Deletes all numbers.

[<B]

-

[C>]

Confirms the selected number.

Side 2

-

[0]

to

[9]

Enters the number.

[*]

Password Confirmation

[#]

Press: Deletes a number.
Hold: Deletes all numbers.

PTT

switch

-

[C>]

key

[C>]

key

[S]

or

[*]

key

When the correct password is entered.

An incorrect
password is
entered.

Mode Reset Timer
is expired without
any operations.

Power-on

1st digit entry

2nd digit entry

1st digit is confirmed.

2nd digit is confirmed.

The last digit is confirmed.

Selector

Selector

«
...
34
35
36
37
38
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

DVDLS91 - PORTABLE DVD PLAYER

Brand: Panasonic Pages: 32

Brand: Baofeng Pages: 7

Brand: E-Tech Pages: 14

Brand: Hama Pages: 30

Brand: Hama Pages: 30

Brand: Hama Pages: 18

Badradio SR-500

Brand: Hama Pages: 5

Brand: Hama Pages: 42

Brand: Hama Pages: 46

Brand: Hama Pages: 64

Brand: Hama Pages: 66

Brand: Hama Pages: 29

Brand: Hama Pages: 50

Brand: Samyung ENC Pages: 23

Brand: Zenith Pages: 9

Brand: Ubiquiti Pages: 33

Brand: Sirius XM RAdio Pages: 26

Brand: Ramsond Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands