manualshive.com logo in svg

Kenwood NX-5000 series, Manual

Share
Download
Kenwood NX-5000 series Manual Download Page 65

1.9

Sending GPS Data

Global Positioning System (GPS) is the system to acquire the current location information of the own transceiver by receiving
signals from the Global Positioning System satellites orbiting the earth.
The transceiver of the mobile station can send the acquired own location information (GPS data) to the base station. The
base station can send received GPS data to the PC as serial commands.
In a P25 Conventional system, the location information received from the built-in GPS receiver unit or the GPS receiver unit
connected to the transceiver can be sent to the parties that are registered beforehand using Tier 1 Location Service compliant
with TIA-102.BAJB and the P25 CAI of P25 Conventional.

Note

0

GPS data is not sent in the non-positioning state that the location information is not received from the GPS receiver unit.
The “

” icon blinks in the non-positioning state. (Refer to Common FUNC 

The Icons on the LCD

.)

0

The transmission of GPS data sent on a P25 Conventional channel with Encryption enabled will not be encrypted. (Refer
to 

COMMUNICATION SECURITY

.)

Transmission Method of GPS Data

The following are the methods to send GPS data:

0

Manual GPS data transmission

(Refer to 

Sending GPS Data Manually by Using a Key (Send the GPS Data)

.)

0

Automatic GPS data transmission

(Refer to 

Sending GPS Data Automatically (Auto GPS Report)

.)

0

GPS data transmission linked with operation of the PTT switch

(Refer to 

Sending GPS Data Linked With the PTT Switch Operation (GPS Report)

.)

0

GPS data transmission linked with operation of turning the transceiver ON and OFF

(Refer to 

Sending GPS Data Linked With the Operation of Turning the Transceiver ON and OFF (GPS Report)

.)

0

GPS data transmission linked with an Emergency Call

(Refer to 

Sending GPS Data in Emergency Mode (GPS Report)

.)

0

GPS data transmission linked with travel distance

(Refer to 

Sending GPS Data Based On Travel Distance (GPS Distance Change)

.)

1 P25 CONVENTIONAL SYSTEM

1.9 Sending GPS Data

P25 FUNC (K)/Ver 2.20

45

CONTENTS

INDEX

Summary of Contents for NX-5000 series









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands