28
C-616DV
English
29
System setup
Setting Auto Power Save (A.P.S.)
A.P.S. stands for Auto Power Save, which is the
function that switches this unit OFF when it has not
been controlled for more than 30 minutes while its
power is ON and the CD and other inputs are in stop
mode.
1
Press TIMER SET button.
2
Press MULTI CONTROL
2
or
3
button to select
"A.P.S." and press ENTER button.
3
Press MULTI CONTROL
2
or
3
button to select
the A.P.S. setting and press ENTER button to
store the setting.
Setting
Function
A.P.S. ON
A.P.S. mode is ON.
A.P.S. OFF
A.P.S. mode is OFF.
When the setting completes, "COMPLETE" is
displayed and the unit exits the setup mode
automatically.
When the A.P.S. is ON...
A.P.S. is activated when this unit is in either
condition below.
• When the input source is TUNER, AUX, D.AUDIO, or iPod,
the volume level is 0 and no button has been pressed for
30 minutes.
• When the input source is CD, USB or SD, the CD player or
USB device or SD is in stop mode and no button has been
pressed for 30 minutes.
⁄
• When the A.P.S. is activated, the display shows flashing "A.P.S."
from about one minute before this unit is switched OFF.
In case of diffi
culty
remote control and make sure that you are
pointing at unit’s remote sensor.
"ON SCREEN" is displayed on main unit.
\
Confi rm the operation on the monitor. Operate
on the monitor if necessary.
lens has cleared.
NO picture.
\
Place the disc on the disc tray correctly inside
the guide.
\
Clean the disc.
\
Select the appropriate video input model on
the TV so the picture from the unit appears on
the TV.
USB operation
"NO USB" is displayed.
\
Press button again after pressing
button.
\
Insert the USB device properly.
"NOT SUPPORT" is displayed.
\
Press button again after pressing
button.
Cannot play.
\
Check if the USB mass storage class-
compatible digital audio player is turned ON.
iPod operation
"NO iPod" is displayed.
\
Insert the iPod properly.
Does not function properly.
\
Disconnect the iPod and connect it again.
\
Check the software version of the iPod. If it is
not the latest one, update it.
SD operation
"NO SD" is displayed.
\
Press button again after pressing
button.
\
Insert the SD card properly.
"NOT SUPPORT" is displayed.
\
Press button again after pressing
button.
Cannot play.
\
Insert an SD card containing music fi les.
D.AUDIO operation
Kenwood digital audio player cannot be
controlled from the main unit or remote control
unit.
\
Connect using the connection cable
(separately available).
\
Check if a compatible model is connected.
Remote control unit
Does not function properly.
\
Replace the batteries.
\
Remove the obstacles.
\
Move closer to the system when using the
Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be
operated, or shows an erroneous display) if the power
cord is unplugged while the power is ON, or due to
some other external factor. If this happens, execute
the following procedure to reset the microcomputer
and return the unit to its normal operating condition.
When the "NO DISC" mode or "OPEN" mode (DVD
source without a disc in the unit), press and hold
down the [SOUND] button on the main unit for
more than 2 seconds.
Unplug the AC cord and plug it back in if
"FACTORY RESET FINISHED" is appears.
• Please note that resetting the microcomputer will clear the
contents of the memory and return the unit to the state it
was in when it left the factory.
Check that following guide for problem resolution.
General
No sound.
\
Plug in AC cord securely.
\
Set the VOLUME control to proper sound level.
\
Make sure the source is set to the source you
want to operate.
\
Pull out the headphones plug from the
headphones jack.
The left and right sound outputs are reverse.
\
Check the speaker connections and location.
The system does not operate by pressing any
buttons.
\
Unplug the AC cord and plug it back in.
This unit is turned OFF spontaneously.
\
A.P.S. is set to ON. Set it to OFF.
Radio reception
Noise in radio.
\
Tune to a correct frequency.
\
Adjust the direction of the FM antenna.
\
Adjust the position and direction of the AM
antenna.
\
Increase the distance between the system and
TV or VCR.
DVD player operation
“NO DISC” is displayed.
\
Insert a disc correctly (label side up).
\
Clean the disc.
\
Use a new or readable disc.
\
Wait until the moisture condensation at the
B60-5820̲08̲00̲C-616DV̲English.indd 28-29
09/10/01 15:12