TOOL STAND
ASSEMBLY INSTRUCTIONS
STYLE NOS. TS261, TS261X (26 Inches Wide)
BEFORE ASSEMBLY OF YOUR TOOL STAND
Check carefully to ensure that all parts listed on the
reverse side are included. If any are missing, please call
800-413-8665 and ask for the Sales Dept. Do not discard
packing material until assembly is complete.
TOOLS REQUIRED
Flat tip screwdriver—Main Assembly
7/16” Open end wrench or socket wrench—Main Assembly
3/8” Open End or Socket Wrench—Top Assembly Square
KMC Holdings LLC dba Kennedy Manufacturing Company
1260 Industrial Drive • Van Wert, OH 45891
Phone 800-413-8665 • Fax 419-238-5644 • www.kennedymfg.com
Part No. 527053, Rev. 10/07
�
�
�
�
�
�
�
�
�
�������������������
������������
�
�
�
To order additional drawers, refer to your Kennedy Catalog:
• Four drawers, catalog no. DR264 with frictions slides for
Model TX261, or DR264X with ball-bearing slides for Model
TS261X
CAUTION
DO NOT SLIDE OR MOVE UNIT
FULLY LOADED. MAY RESULT
IN DAMAGE OR INJURY.
FIG. 1
KMC
Packer User Key Qty
Parts Description
A
2
End Panels
B
2
Inner Panels
C
4
Rails
D
1
Shelf
E
1
Drawer Stop
F
1
Back Wall Panel
G
1
Bench Top
H
32
1/4” x 1/2” Bolts, Lock Washers, Hex Nuts
I
4
Adjustable Leg Leveler
J
4
#14-5/8” Hex Screws (Top Assembly)
K
1
Drawer
L
1
Drawer Pull
M
2
#8-18 x 3/8” Hex Head Sheet Metal Screw
(not shown)
N
1
82187 Snap-in Friction Slide Set
Model No. TS261 Parts Check List
KMC
Packer User Key Qty
Parts Description
A
2
End Panels
B
2
Inner Panels
C
4
Rails
D
1
Shelf
E
1
Drawer Stop
F
1
Back Wall Panel
G
1
Bench Top
H
32
1/4” x 1/2” Bolts, Lock Washers, Hex Nuts
I
4
Adjustable Leg Leveler
J
4
#14-5/8” Hex Screws (Top Assembly)
K
1
Drawer
L
1
Drawer Pull
M
2
#8-18 x 3/8” Hex Head Sheet Metal Screw
(not shown)
N
1
82183 Ball-Bearing Slide Set
Model No. TS261X Parts Check List
Step 7. SLIDE AND DRAWER ASSEMBLY
Note:
This unit may be equipped with either I-beam friction slides
or ball-bearing slides. Refer to the appropriate instructions below.
I-Beam Friction Slides
Each drawer requires six slide parts, See
Fig. 8
:
a. one 270 DR LH; one 270 DR RH—attaches to drawer
b. one FE LH; one FE RH—attaches to inner panel
c. two male slides with springs
Note:
LH/RH refers to Left and Right Hand—part numbers are
marked on a. & b.
1. Insert rear horizontal tab of b. (FE RH) into back square hole
second row from top on right side inner panel. Line up center and
front tabs with matching square holes and snap
down
into place,
locking in the slide.
2. Repeat above step 1 on left side inner panel.
3. Attach a. 270 DR LH and RH (left hand and right hand) to drawer
sides, inserting rear horizontal tab into back square hole. Line up
center and front tabs with matching square holes and snap
up
into
place. Repeat with remaining drawers.
4. Insert c. (male slides) fully into channel of inner panel slides so
that spring at back of unit faces drawer and front spring faces inner
panel.
See Fig. 10
. Make sure spring stop is engaged. (This prevents
drawer from being pulled all the way out of unit).
5. Pull male slides, left and right, partially out—align drawer to male
slides—insert male slides into drawer slides and firmly push drawer
all the way in for engagement.
Ball-Bearing Slides
Each drawer requires one ball-bearing slide set consisting of one
right and one left hand triple member ball-bearing slide.
See Fig. 11
.
Note:
Large side of slide attaches to inner panel while smaller
member detaches and then is fixed to drawer. Both have one
horizontal and one vertical facing locking tab.
1. Insert rear horizontal tab (closest to black plastic detente) on large
member into back square hole second row from top on right side
inner panel. Align front tab with matching square hole and snap
down
into place, locking in the slide. (
Note:
If front tab faces up,
you incorrectly have the left side slide).
2. Repeat above procedure 1 on left side panel.
3. Starting at right side panel, fully extend slide small member
(drawer side). Depress plastic release lever and remove member.
Install it on drawer right side by inserting rear horizontal tab into
drawer rear square hole. Align front tab to matching hole and snap
up
into place, locking in the slides.
4. Repeat procedure on left side of drawer.
5. Align drawer slide members with inner panel slides, inserting
them back into place. Push drawer evenly all the way into slide and
pull out to make sure slide members are correctly joined.
Step 11. Install Drawer Pull
1. Attach drawer pull (L)—
see Fig. 1
—with two hex head slotted
screws (M) per drawer, using a flat-tip screwdriver.
���������������
Fig. 8
Fig. 9
Fig. 10
������������������
Black Plastic
Detente
Panel
Member
Inner
Member
Drawer
Member
Fig. 11
a.
b.
c.
�����������
������
�
�
�
�
�
