background image

Installation
Instructions

Built-In
Dishwasher

If you have questions,

 call 1-800-4-MY-HOME 

®

 (1-800-469-4663) or visit our website at:

www.sears.com

IMPORTANT

 –

     

The dishwasher MUST

be installed to allow for future removal from the enclosure if

service is required.
If you received a damaged dishwasher, you should immediately

contact your dealer or builder.

Optional Accessories –

 See the Owner’s Manual for

available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While
performing installations described in this booklet,
gloves, safety glasses or goggles should be worn.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IMPORTANT

 –

     

Observe all governing

codes and ordinances.

Note to Installer –

 Be sure to leave these instructions for

the consumer's and local inspector's use.

Note to Consumer –

 Keep these instructions with your

Owner’s Manual for future reference.

Skill Level –

 Installation of this dishwasher requires basic

mechanical and electrical skills. 

Proper installation is the

responsibility of the installer. Product failure due to
improper installation is not covered under the
SEARS Appliance Warranty.

Completion Time – 1 to 3 Hours.

 New installations require

more time than replacement installations.

WARNING

To reduce the risk of electrical shock, fire, or

injury to persons, the installer must ensure that

the dishwasher is completely enclosed at the

time of installation.

READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

Summary of Contents for 66515751791













Reviews: