manualshive.com logo in svg

Kenmore 106.5133 Series, Use & Care Manual

Share
Download
Kenmore 106.5133 Series Use & Care Manual Download Page 15

15

6. 

Insert the filter into the housing. 

7. 

Twist the water filter and turn 90

°

 clockwise until it locks into 

place and the arrows are aligned.

8. 

Push the water filter door closed. 

ICE MAKER AND STORAGE BIN

 

■

Allow 24 hours to produce the first batch of ice. Discard the 

first three batches of ice produced. 

 

■

The quality of your ice will be only as good as the quality of 

the water supplied to your ice maker. Avoid connecting the ice 

maker to a softened water supply. Water softener chemicals 

(such as salt) can damage parts of the ice maker and lead to 

poor quality ice. If a softened water supply cannot be avoided, 

make sure the water softener is operating properly and is well 

maintained.

 

■

Do not use anything sharp to break up the ice in the storage 

bin. This can cause damage to the ice container and the 

dispenser mechanism.

 

■

Do not store anything on top of or in the ice maker or  

storage bin.

Turning the Ice Maker On/Off

 

■

The On/Off switch, located on the left wall of the freezer 

door, can only be accessed when the ice storage bin has been 

removed. See the following section for bin removal instructions. 

ON

OFF

 

■

To turn on the ice maker, flip the switch to the On (up) position.

 

■

To manually turn off the ice maker, flip the switch to the Off 

(down) position. 

NOTE: 

Your ice maker has an automatic shut off to keep the 

storage bin from overfilling during normal operation. As ice is 

made, the ice cubes will fill the ice storage bin, and the ice cubes 

will raise the shut off arm to the Off (up) position. When the 

storage bin is at full capacity, the ice maker will automatically 

stop ice production, but the ice maker On/Off switch will remain 

in the On (up) position. 

Removing and Replacing the Ice Storage Bin

1. 

Press down the release lever and tilt the bucket outward. Use 

both hands to hold the base of the storage bin, then lift it up 

and out. 

A

NOTE:

 It is not necessary to turn the ice maker control to the 

Off (right) position when removing the storage bin. The sensor 

cover (“

flipper door

”) on the left wall of the freezer stops the ice 

maker from producing ice if the door is open or the storage bin is 

removed.  

A

B

2. 

Replace the bin by sliding it onto the door, then tilting it back 

into an upright position. The release lever will click when the 

bin is securely in place.

Ice production off 

(shut off arm up)

Ice production on 

(shut off arm down)

A. On/Off switch

B. Storage bin sensor

A. Release lever.

Summary of Contents for 106.5133 Series



























Reviews:

No comments

Brands by name

Popular brands

Load more brands