Kemppi Flexlite GX 203G Operating Manual Download Page 20 | Manualshive

Page: 20 / 49

background image

Flexlite GX

Operating manual - EN

3.8 Installing and removing grip handle (optional)

The additional grip handle is available for all Flexlite GX MIG welding guns.

1.

Keeping the bottom of the grip handle pointing forward, fit the inside grooves of the grip handle over the
screws on the gun.

2.

Pull the handle backward to lock it in position.

To remove the grip handle, press the unlock button in the grip handle rear:

© Kemppi

21/49

1921390 / 2002

«
...
18
19
20
21
22
...
»

Summary of Contents for Flexlite GX 203G


















































Reviews:

No comments

Related manuals for Flexlite GX 203G

Brand: Vector Welding Pages: 81

Brand: KAM Pages: 4

Brand: PartyFunLights Pages: 4

Brand: jablotron Pages: 16

Brand: Magnavox Pages: 24

Brand: Magnavox Pages: 22

Brand: Magnavox Pages: 21

Magnavox FW 750C

Brand: Magnavox Pages: 28

Magnavox FW 2012

Brand: Magnavox Pages: 16

Brand: Panasonic Pages: 89

Brand: M&K Sound Pages: 15

Brand: Bose Pages: 44

IP Surveillance

Brand: Vivotek Pages: 73

Brand: Aiwa Pages: 30

Brand: Faraone Pages: 68

Brand: Eaton Pages: 40

Brand: Campbell Hausfeld Pages: 68

Brand: Skytec Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands