manualshive.com logo in svg

Keithley 7012-C, Instruction Manual, Page: 31 / 93

Share
Download
Keithley 7012-C Instruction Manual Download Page 31

 

Card Connections & Installation

 

3-4

 

3.3.3 Multi-pin (mass termination) connec-

tor card 

 

Since connections to external circuitry are made at the
96-pin male DIN bulkhead connector, there is no need
to separate the connector card from the relay card. If
the connector card is separated from the relay card,
carefully mate them together. Make sure to handle the
cards by the edges and shields to avoid contamination. 

Figure 3-4
Cable clamp for screw terminal connector card

Clips

Screw

 

Terminal identiÞcation for the DIN connector of the
multi-pin connector card is provided by Figure 3-5.
This connector will mate to a 96-pin female DIN con-
nector. 

Keithley has a variety of cable and connector accesso-
ries available to accommodate connections from the
connector card to test instrumentation and DUT (de-
vices under test). In general, these accessories, which
are summarized in Table 3-1, utilize a round cable as-
sembly for connections.

 

Table 3-1

 

Mass termination accessories

 

Model

Description

 

7011-KIT-R

96-pin female DIN connector and 
housing for round cable.

7011-MTC-2

Two-meter round cable assembly 
terminated with a 96-pin female 
DIN connector on each end.

7011-MTR

96-pin male DIN bulkhead connec-
tor.

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Summary of Contents for 7012-C






























































































Reviews:

No comments