Keithley 7012-C Instruction Manual Download Page 20

Page: 20 / 93

2-3

2.3

Typical matrix switching schemes

The following paragraphs describe some basic switch-
ing schemes that are possible with a two-pole switch-
ing matrix. These switching schemes include some
various shielding con

gurations to help minimize

noise pick up in sensitive measurement applications.
These shields are shown connected to chassis ground.
For some test con

gurations, shielding may prove to

be more effective connected to circuit common. Chassis
ground is accessible at the rear panel of the Model 7001.

2.3.1 Single-ended switching

In the single-ended switching con

guration, the source

or measure instrument is connected to the DUT
through a single pathway as shown in Figure 2-4.

Figure 2-4
Single-ended switching example

Source or

Measure

Row

Columns

7012

DUT

Optional

Shield

Figure 2-3
Matrix row connections to backplane

7001

Analog

Backplane

7012

Matrix Row

(1 of 4)

Backplane

Jumpers

H = High
L = Low
G = Guard

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Summary of Contents for 7012-C






























































































Search results

Summary of Contents for 7012-C

Reviews:

Keithley 7012-C, Instruction Manual, Page: 20 / 93

Search results

Summary of Contents for 7012-C

Reviews: