SCPI Command Reference
17-37
Composite testing
PASS:SOURce2 <NRf> | NDN
:CALCulate2:CLIMits:PASS:SOURce2 <NRf> | <NDN>
Specify composite
“
pass
”
pattern
Parameters
<NRf> =
0 to 7 (3-bit)
Decimal value
0 to 15 (4-bit)
Decimal value
<NDN> =
0 to #b111 (3-bit)
Binary value
0 to #b1111 (4-bit) Binary value
0 to #q7 (3-bit)
Octal value
0 to #q17 (4-bit)
Octal value
0 to #h7 (3-bit)
Hexadecimal value
0 to #hF (4-bit)
Hexadecimal value
Query
:SOURce2?
Query programmed source value
Description
This command is used to de
fi
ne the 3-bit or 4-bit output pattern for the Dig-
ital I/O Port when there are no failures. Note that the output value can be
speci
fi
ed in binary, octal, decimal, or hexadecimal format. Use the table pro-
vided in
:SOURce2<NRf> | <NDN>
,
Description
to determine the parame-
ter value for the desired decimal digital output pattern.
The SourceMeter can be con
fi
gured to place the de
fi
ned
“
pass
”
bit pattern
on the digital output immediately when the
“
pass
”
condition occurs, or it
can wait until all testing on a device package is completed (operation leaves
trigger layer). See :BCONtrol for details.
For the sorting mode, this command de
fi
nes the 3-bit or 4-bit output
“
pass
”
pattern for the Limit 1 test (compliance) when Limits 2, 3, and 5-12 are
disabled.
NOTE
16-bit I/O is available with the 2499-DIGIO option. The maximum 16-bit output
value is 65535.
FAIL:SOURce2 <NRf> | <NDN>
:CALCulate2:CLIMits:FAIL:SOURce2 <NRf> | <NDN>
Specify
“
fail
”
pattern
Parameters
<NRf> =
0 to 7 (3-bit)
Decimal value
0 to 15 (4-bit)
Decimal value
<NDN> = 0 to #b111 (3-bit)
Binary value
0 to #b1111 (4-bit) Binary value
0 to #q7 (3-bit)
Octal value
0 to #q17 (4-bit)
Octal value
0 to #h7 (3-bit)
Hexadecimal value
0 to #hF (4-bit)
Hexadecimal value
Query
:SOURce2?
Query programmed source value
Description
For the sorting mode, this command is used to de
fi
ne the 3-bit or 4-bit
output pattern for the Digital I/O Port when there are failures. Note that the
output value can be speci
fi
ed using binary, octal, decimal, or hexadecimal
format. Use the table provided in
:SOURce2<NRf> | <NDN>
,
Description
to determine the decimal parameter value for the desired digital output
pattern.
Summary of Contents for 6430
