KEEWAY F-ACT EVO Page 46 Instruction & Maintenance Manual Download

Page: 46 / 156

- 45 -

Install the oil level gauge.

* Note

Confirm whether the bolts wear or not.

Gear oil replacement

Remove the gear oil to check bolt

Remove the oil bolt, make the gear oil flow out

Fix the oil bolt.

Note:

Confirm whether the bolts wear or not.

Supplement gear oil,

Check if there is leaking oil

Install gear oil to check bolt

Drive belt

Remove the cover of left crank case.

Check whether the drive belt is work or damaged.

Periodically maintenance shall be guaranteed, and replace the

drive belt with a new one if necessary.

驱动皮带：

drive belt

Free path of front/rear brake

Free path of front brake

Measure the free path of front brake at the point of the brake

lever.

Free path: 10-20mm

Summary of Contents for F-ACT EVO





























































































































































Search results

Summary of Contents for F-ACT EVO

Reviews:

Related manuals for F-ACT EVO

Brands by name

Popular brands

KEEWAY F-ACT EVO, Instruction & Maintenance Manual

Search results

Summary of Contents for F-ACT EVO

Reviews:

Related manuals for F-ACT EVO

Brands by name

Popular brands