manualshive.com logo in svg

Kees van der Westen Slim Jim mirage, User Manual

Share
Download
Kees van der Westen Slim Jim mirage User Manual Download Page 14

USER MANUAL - operation 

Slim Jim User manual 

 

page 13 

Start automatic back-flush program 

See paragraph “

Back flush group

” on page 22 for complete back-flush procedure

. 

When the machine is in “normal” operational mode touch the MENU icon on the interface.  
In the next screen touch the button 

“CLEAN PROGRAM”.  

operational window

 

 

 

 

 

 

 

 

touch 

 

 

 

 

 

 

 

 

menu window

 

 

 

 

 

 

 

touch 

 

 

 

 

 

 

 

 

 

 

This will start the cleaning program. The display will 

immediately return to the upper (operational) window.

 

 

 
The groups will pressurise (duration: 16 seconds) and de-pressurise (duration: 10 seconds) 8 times 
successively and then the machine will return to normal operation. Indicator LED(s) on the 
corresponding Bastone unit or touchpad will flash during the cleaning program. 

Note!  

If a group is activated during the back-flush program, the group valve of that group will de-activate but 
the back-flush routine will continue on the other group(s). 
When all groups are manipulated, the group valves will all close but the pump will finish the back-flush 
routine. 

 

Flow meter error 

When flow rate of a group becomes very low or stops, the flow-meter is not able to accurately 
measure the amount of water passing through and the display will show an error message. 

operational window

 

 

group 3 shows a 

flow-meter error

 

This will not affect any ongoing action of the machine but “volume in the cup” may not be as 
programmed. The error message will remain visible until the group is activated a next time. 

The error message will not be shown during the cleaning program (automatic back-flush program). 

 

 

GROUP 1

93.4

GROUP 2

45.6

GROUP 3

93.2

STEAM

124.6

MENU

STAND

BY

EXTERNAL

SENSOR

CLEAN

PROGRAM

SETTINGS

13 : 57

GROUP 1

93.4

GROUP 2

45.6

GROUP 3

flow m.

STEAM

124.6

MENU

Summary of Contents for Slim Jim mirage


































Reviews:

No comments

Brands by name

Popular brands

Load more brands