background image

44

Scaling and weighting 

ServoOne User Manual SERCOS II and III

ID no.: 1108.26B.3-00     Date: 04/2020

Scaling and weighting 

Bits 2-0

Weighting type

0 0 0

No weighting

0 0 1

Translatory weighting

0 1 0

Rotary weighting

Bit 3

Weighting method

0

Preferred weighting

1

Parameter weighting

Bit 4

Unit

0

Degree (for rotary weighting) / meter (for translatory weighting)

1

Reserved (for rotary weighting) / inch (for translatory weighting)

Bit 5

Reserved

Bit 6

Data reference

0

At the motor shaft

1

On the load side

Bit 7

Processing format

0

Absolute format

1

Modulo format

Bit 8-15

Reserved

Table 8.4 

Bit fields in the position data weighting type parameter (S-0-0076)

The following figure shows the various possibilities for the position weighting.

Figure 8.1 

 

 

LSB = 10  m 

-7 

LSB  

(S-0-0077) 

(S-0-0078) 

LSB 

(S-0-0079) 

S-0-0076 bit 0–2 

S-0-0076 bit 6 

S-0-0076 

bit 3 

S-0-0076 

bit 4 

3600000 

LSB = 0.0001  

rotary

translatory

none

Position data weighting type (S-0-0076)

Dregree

Load/Motor

Dregree

Resolution:

Parameter 

weighting

Dregree

Load/Motor

Load/Motor

Metre

Metre

variable

variable

Preferred 

weighting

Preferred 

weighting

Parameter 

weighting

 Diagram of the position weighting types

Summary of Contents for ServoOne Series























































































Reviews: