manualshive.com logo in svg

Keba KeTop T50VGA, User Manual, Page: 33 / 165

Share
Download
Keba KeTop T50VGA User Manual Download Page 33

Handheld Terminal 

Connection 

User's Manual, Version: 1.3 

33 

© KEBA 2007 

 

4.7 Ethernet 

The standard version of the KeTop is equipped with an Ethernet interface. 
This interface is based on the 10BaseT specification and suitable for the 
half-duplex mode (the operation with 100Mbit requires a special connection 
cable) 
 
The data communication for these interfaces takes place via the Ethernet 
connector S4 (marking: ETHERNET) in the cable entrance area of the Ke-
Top.  
 
The following interface parameters are defined and cannot be changed: 
 

z

 

10 MBit (100MBit with appropriate cable possible) 

z

 

TCP/IP protocol 

 
The Ethernet interface is selected under Windows CE as follows: 
 

Start -> Settings -> Control Panel  -> Network and Dial-up Connections: 

Here you can select the Ethernet on-board interface 

SMSC911x1

. 

 

!

 

WARNING! 

•

 

If the KeTop and the control do not communicate via a point-to-point 
connection, it may happen that the keypad data, for example, are 
transmitted with a delay.  
 
Therefore it is advisable to establish the connection between the con-
trol and the KeTop only via an Ethernet switch which enables a point-to-
point connection. 

 
The positions of the Dip switches in the cable entrance area are not rele-
vant for this interface. 
 

Information 

•

 

The simultaneous use of the Ethernet interface and the COM interface 
(RS-422-A or RS-232-C) is only possible with an appropriate cable . 

 
 
 

Summary of Contents for KeTop T50VGA






































































































































































Reviews:

No comments