KEB COMBIVERT S6 Series Instructions For Use Manual Download

Page: 39 / 66

3.3.9 fan

Unit size

Heat sink fan

Number

Speed-variable

—

Table 22: Fan

NOTICE

Destruction of the fan!

►

Take care that no foreign substances drop into the fan!

3.3.9.1 Switching behaviour of the fan

The fan has different switch-on and switch-off points. The switching point for the switch-

on temperature

①

of the fan is adjustable. The switching point for the switch-off temper-

ature

②

cannot be changed and is always 5°C below the switch-on temperature.

100

①

②

Temperature / °C

Fan speed / %

Legend

Temperature curve
Setting range for the switch-on temperature

①

Switch-on point

②

Switch-off point

Figure 8:

Switching behaviour of the fan

3.3.9.2 Switching points of the fan

The switching point for the switch-on temperature is adjustable between 0.1°C and

50°C. The default value is 50°C.

UNIT DATA

Summary of Contents for COMBIVERT S6 Series



































































Search results

Summary of Contents for COMBIVERT S6 Series

Reviews:

Related manuals for COMBIVERT S6 Series

Brands by name

Popular brands

KEB COMBIVERT S6 Series, Instructions For Use Manual

Search results

Summary of Contents for COMBIVERT S6 Series

Reviews:

Related manuals for COMBIVERT S6 Series

Brands by name

Popular brands