manualshive.com logo in svg

KEB COMBIVERT F5-A, Applications Manual, Page: 211 / 552

Share
Download
KEB COMBIVERT F5-A Applications Manual Download Page 211

Motor data and controller adjustments of the synchronous motor

© KEB, 2012-10

COMBIVERT F5-A, -E, -H

Page  7.6 - 11

7

dr.48 Motor identification

Bit

Description

Value

Function

0...4

Measurement

0:  off

1:  Calculation EMC *

Calculation of the EMC from motor data

2:  Inductance *

Measurement of the winding inductance respec-
tively

3:  Resistance *

Winding resistance

5: Model-/controller parameterisa-
tion *

Calculation of the current controller from equiva-
lent circuit data

6:  EMC with rotation *

Attention: requires motor rotation!

EMC measurement

7: Automatically sequence without 
rotation

Start of the automatic measurement without EMC

8:  Automatically sequence with 
rotation

Start of the automatic measurement with EMC

9:  Dead time detection 2 kHz *

Measurement of dead time compensation cha-
racteristics for different switching frequencies

10: Dead time detection 4 kHz *

11: Dead time detection 8 kHz *

12: reserved

13: Dead time detection 16 kHz *

14: Torque detection 2 kHz

Detection of the no-load torque at different swit-
ching frequencies. During operation this torque is 
subtracted from torque display ru.12.

15: Torque detection 4 kHz

16: Torque detection 8 kHz

17: reserved

18: Torque detection 16 kHz

19: Current offset detection

Detection of the current offset in phase U and V

20: reserved

5...7

Frequency

0:   1000Hz

The measuring frequency is changed indepen-
dently during measurement.

Therefore, leave the value at 0: keep 1000Hz!

32:  500Hz

64:  250Hz

96:  125Hz

128: 62.5Hz

160: 32.25Hz

192: 15.625Hz

224: 7.8125Hz

* at dr.48 = 8 auto-identification

7.6.3.3.1 

Auto-identification

The 

automatic identification can be carried out with rotation (dr.48=8) or without rotation (dr.48 = 7) (see table 

dr.48). The measurement of the dead time compensation characteristics as well as stator resistance and lea-
kage inductance occurs during standstill. 

For EMC identification it is necessary to accelerate the motor onto 60% of its rated speed. For this case an 

additional ramp of dr.49 "Lh ident. acc/dec time" is effective". Calculation of the ramp can be taken from chapter 
7.6.3.4.

Summary of Contents for COMBIVERT F5-A









































































































































































































































































































































































































































































































































































Reviews:

No comments