manualshive.com logo in svg

KEB COMBIVERT F4-F, Applications Manual, Page: 220 / 300

Share
Download
KEB COMBIVERT F4-F Applications Manual Download Page 220

6

11

KEB COMBIVERT F4-F

10

Name: Basis

17.06.99

Chapter

Section

Page

Date

©

KEB Antriebstechnik, 1999
All Rights reserved

Functional Description

Positioning Module

Limit of position controller

(Pd.3)

Adjustment of the speed difference which the position controller may add to the profile
of the speed precontrol. The maximum setpoint speed for the positioning is calculated
from Pd.7 + Pd.3. Pd.3 can be set to 0,0...500,0 revolutions.

S-curve time (Pd.5)

For positionings that require a jerk-free starting s-curves are adjustable with Pd.5,
which are executed during acceleration and deceleration. The total acceleration time
is calculated from Pd.6 + Pd.5 (see Fig. 6.11.11). The S-curve time is adjustable in
the range of 0,01...8,00 s.

Acceleration time (Pd.6)

Adjusts the acceleration time in the range of 0,01...8,00 s. In case the torque limit is
reached during a positioning procedure the required torque can be lowered by
extending the acceleration time.

Maximum speed (Pd.7)

With Pd.7 the maximum speed of the precontrol profile is defined. The adjusted value
may be exceeded maximally by the speed difference of the position controller (Pd.3).
But the absolute maximum frequencies (SP.8 / SP.9) cannot be exceeded.

6.11.13 Optimizing Posi-

tion Controller
(Pd.2)

With Pd.2 the position controller can be individually optimized for every approached
position. Provided that the total position adjustment supplies satisfactory results, an
optimization can be become necessary in following cases:

• target position is not reached
• drive moves beyond the target position and returns then

This may be caused by a position controller which is adjusted too smooth.With Pd.2
the controller can be adjusted in the range of 0....65535 (default value 20).

6.11.14 Teach - Function

(Pd.1)

With the Teach-function positions are manually approached and stored in the
respective set by switching from Pd.1 to „3“. The Teach-function is only possible for
absolute setpoint positions.
Procedure:

• Activate positioning module (Pc.0 = 1)
• Deactive positioning (Pd.0 = 0)
• Approach the desired position at low speed (e.g. with jogging)
• Select the set, in which the position shall be stored (by way of digital

inputs or parameter Fr.4)

• Actual position is stored as setpoint position in the selected set  (switch

Pd.1 to 3)

• Approach the next position
• Select the next set
• Actual position is stored as setpoint position in the selected set (switch

Pd.1 to 3 )

• and so forth

Angular difference (ru.27)

At activated positioning module the contouring error (deviation of actual position to
setpoint profile) is indicated in ru.27 in steps of 0.1 degree.

Summary of Contents for COMBIVERT F4-F













































































































































































































































































































Reviews:

No comments