KEB COMBISTOP 38 Instruction Manual Download Page 30 | Manualshive

Page: 30 / 48

background image

Optional Components and Accessories

30

©

2021 KEB America, Inc.

5 Optional Components and Accessories

The Size 09 COMBISTOP Load Brake has several optional components and accessories

that can be ordered with the brake or separately as an upgrade kit. The following sections

contain instructions on installing these optional components.

Optional Components and Accessories

Component

Part Number

Hand Release Lever

0938520-M01U

Microswitch

0938270-M01U

Table 4 Optional Accessories

5.1 Hand Release Lever

Part Number:

0938520-M01U

Kit Components

Component

Number Included

Handle

1

Yoke

1

Spherical Bolt

2

Spherical Washer

2

Table 5 Hand Release Components

The optional Hand Release Lever provides a manual backup to the standard electronic

brake release for releasing the brake in power failure situations.
To use the Hand Release Lever, pull directly away from the mounting surface with at

least 70lbs of force.
The handle of the Hand Release Lever can optionally be replaced by a lifting eyebolt as

needed for the specific application.

«
...
28
29
30
31
32
...
»

Summary of Contents for COMBISTOP 38

















































Reviews:

No comments

Related manuals for COMBISTOP 38

Brand: Lenze Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands