manualshive.com logo in svg

KEB COMBISTOP 38, Instruction Manual

The KEB Combistop 38 Instruction Manual is an essential resource for users of this high-quality product. This comprehensive manual is available for free download from our website, ensuring that customers have easy access to all the necessary information to utilize their KEB Combistop 38 effectively.

Share
Download
background image

Installation 

©

 2021 KEB America, Inc. 

 

29 

 

 

 

 

4.5  Testing the Brake Function 

After installing the Load Brake, it is recommended to test the brake function to sure the 

installation was performed successfully. 

1.  Power on the brake with nominal voltage and verify the armature disengages. 

2.  Check for free rotation of the shaft while the brake is powered on. 

3.  Power off the brake and verify the armature engages. 

4.  Check for free rotation of the shaft while the brake is powered off. The shaft should not 

rotate with the brake engaged. 

 

 WARNING 

 

  After performing an emergency stop inspect the brake components 

and test the brake performance before continued use. 

 

 

 

 

 

Summary of Contents for COMBISTOP 38

















































Reviews:

No comments

Related manuals for COMBISTOP 38

Brands by name

Popular brands

Load more brands