KEB COMBISTOP 38 Instruction Manual Download Page 26 | Manualshive

Page: 26 / 48

background image

Installation

26

©

2021 KEB America, Inc.

4.3.2.3 Mount the Hub

1. The Load Brake contains several friction disks which can freely rotate when the brake is

disengaged or disassembled. Ensure the teeth of each friction disk are all aligned in the

same orientation.

•

For ease of assembly an optional alignment tool (6) can be used to hold the friction

disks in place while mounting the hub.

→

See section Required Tools for details on the alignment tool.

2. Mount the hub (5) onto the shaft (4) ensuring the hub is oriented with set screws facing

out.

Figure 8 Hub Installation

3. Align the hub (5) onto the teeth of the friction disks (7) using the alignment tool (6) to hold

the friction disks steady (if used). Some rotation of the hub may be necessary to align all

of the friction disks if the optional alignment tool is not used.

Figure 9 Hub Alignment

4. Align the hub axially on the shaft per the brake specifications.

5. Tighten set screws, clamping color or snap rings to secure the hub in place.

«
...
24
25
26
27
28
...
»

Summary of Contents for COMBISTOP 38

















































Reviews:

No comments

Related manuals for COMBISTOP 38

Brand: Kendrion Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands