KEB COMBILINE 07Z2F04-1003 Instructions For Use Manual Download

Page: 11 / 54

bASIc SAFETy INSTRUcTIONS

cAUTION

Maximum design edges and high weight!

contusions and bruises!

►

Never stand under suspended loads.

►

Wear safety shoes.

►

Secure drive converter accordingly when using lifting gear.

•  To prevent damages to the device:
•  Make sure that no components are bent and/or isolation distances are changed.
•  The device must not be put into operation in case of mechanical defects. Non-

compliance with the applicable standards.

• Do not allow moisture or mist to penetrate the unit.
•

Avoid dust permeating the device. Allow for sufficient heat dissipation if installed in

a dust-proof housing.

• Note installation position and minimum distances to surrounding elements. Do not

cover the ventilation openings.

•

Mount the drive inverter according to the specified degree of protection.

• Make sure that no small parts fall into the COMBIVERT during assembly and wiring

(drilling chips, screws etc.). This also applies to mechanical components, which can

lose small parts during operation.

•

Check the reliable fit of the device connections in order to avoid contact resistances

and sparking.

• Do not walk-on drive converter.
• The safety instructions are to be kept!

1.3 Installation

DANGER

Do not operate in an explosive environment!

►

The COMBIVERT is not intended for the use in potentially explosive

environment.

Summary of Contents for COMBILINE 07Z2F04-1003























































Search results

Summary of Contents for COMBILINE 07Z2F04-1003

Reviews:

Related manuals for COMBILINE 07Z2F04-1003

Brands by name

Popular brands

KEB COMBILINE 07Z2F04-1003, Instructions For Use Manual

Search results

Summary of Contents for COMBILINE 07Z2F04-1003

Reviews:

Related manuals for COMBILINE 07Z2F04-1003

Brands by name

Popular brands