KAYO MOTOR TT 125 Service Manual Download Page 56 | Manualshive

Page: 56 / 74

background image

Magneto, timing chain

Matters needing attention

◆

The removal and installation of the magneto, left cover and double teeth introduced in this section, as long as the

left crankcase cover is removed, without removing the engine can be completed;

◆

For the inspection of magneto, refer to the methods in the section of battery charging system.

Removal of left rear cover

The steps for removing the left rear cover are as follows:
1. Remove the bolts fastening the left rear cover;
2. Remove the left rear cover.

Removal of left front cover

The steps for removing the left front cover are as
follows:
1. Remove 3 GB/T 5787/ M6x32 bolts and 1 GB/T
5787/ M6x50 bolts from the left front cover.
2. Remove the left front cover;
3. Remove the left front cover gasket and two 8 x 12
positioning pins.

Removal of magneto stator

The removal steps of the magneto stator are as follows:
1. Turn the left front cover over and place it on a flat
surface;
2. Remove two GB/T 5787-M6x20 bolts for securing
the stator of the magneto, two GB/T 5783-M5×12 bolts
for securing the trigger, and one GB/T 818-M5× 61
cross-recited pan head screw for securing the small
press wire plate. 1 bolts GB/T 5777-M6 ×14 for
fastening wire harness press plate;
3. Remove the stator of the magneto.

Note:

If the stator of the magneto is subjected to

accidental impact in the process of disassembly and
assembly, such as the stator of the magneto is struck by
a foreign body, it should be replaced with a new stator.

Removal of magneto rotor

«
...
54
55
56
57
58
...
»

Summary of Contents for TT 125











































































Reviews:

No comments

Related manuals for TT 125

Brand: KYMCO Pages: 69

Minirack 6602533 01 01

Brand: hepco & becker Pages: 4

Brand: Sena Pages: 25

California EV V1100

Brand: MOTO GUZZI Pages: 173

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Road Star XV17AWX

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 650

Brand: BMW Pages: 88

Brand: Suzuki Pages: 80

Brand: Honeywell Pages: 8

Brand: Honeywell Pages: 304

Brand: BMW Motorrad Pages: 28

Brand: BMW Motorrad Pages: 170

Brand: IBEX Pages: 3

Gold Wing GL1100

Brand: Honda Pages: 356

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands