KAYO MOTOR TT 125 Service Manual Download Page 14 | Manualshive

Page: 14 / 74

background image

Fuel tank switch

into the carburetor, so as to achieve control effect.

Gear Shifting

Gearshift lever

The shift lever is located on the left side of the engine, which is
operated by stepping on and lifting the shift lever. The 21
TT125 engines are in four-gear gear with constant meshing.

Rear disc brake

Foot brake pedal

The foot brake pedal is located on the right side of the engine
and is operated by stepping.

Note:

when brake, the foot brake should be the main brake,

hand brake as a supplement.

Rear brake caliper

The rear brake adopts a floating clamp disc brake, whose clamp
body is located on the right side of the rear wheel and is fixed
by a disc brake bracket.

Parking stand

«
...
12
13
14
15
16
...
»

Summary of Contents for TT 125











































































Reviews:

No comments

Related manuals for TT 125

Brand: Caberg Pages: 16

Brand: BV Powersports Pages: 40

Brand: NewMar Pages: 116

Brand: Honda Pages: 28

Brand: Honda Pages: 102

Brand: Honda Pages: 143

HPS SafeGuard Series

Brand: Dräger Pages: 40

Brand: TERMOSCUD Pages: 16

Brand: Panther Pages: 47

Brand: N-Com Pages: 14

Prime R1-HD2-9813

Brand: Rockford Fosgate Pages: 18

Brand: OKBABY Pages: 35

Brand: Bikecomm Pages: 15

Brand: Honda Pages: 177

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: Gazzini Pages: 27

RSV4 1100 Factory 2021

Brand: APRILIA Pages: 500

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands