KaVo KEY Laser 3+ 1343 Instructions For Use Manual Download Page 36

Page: 36 / 80

▶ Pull off the handpiece by twisting it axially.

▶ To prevent soiling the hose coupling window ② wipe off the laser hose coupling

with a clean, dry cloth from back to front.

See also: Section A 2.3 Handpiece instructions.

Note
Windows are coated. Do not wipe unnecessarily.

▶ Check if the window ② is clean and dry, and if the O-rings ③ are undamaged.

Note
If a handpiece is not coupled directly afterwards, the laser hose coupling must be

provided with the cap ① and the handpiece with the cap ④. These two caps prevent

the penetration of dirt into the laser hose coupling and the handpiece.

▶ Dry the inside of the handpiece coupling.

4.4

Switching on

Note
Make sure that the emergency-off switch is not pressed. This can be released or

its condition can be checked by turning the red knob to the right. If it was pressed,

it will spring out.

Instructions for use KEY Laser 3+ 1343 KEY Laser III 1243 upgraded
4 Operation | 4.4 Switching on

34/76

Summary of Contents for KEY Laser 3+ 1343

















































































Search results

Summary of Contents for KEY Laser 3+ 1343

Reviews:

Related manuals for KEY Laser 3+ 1343

Brands by name

Popular brands

KaVo KEY Laser 3+ 1343, Instructions For Use Manual

Search results

Summary of Contents for KEY Laser 3+ 1343

Reviews:

Related manuals for KEY Laser 3+ 1343

Brands by name

Popular brands