20
English
Operation
Filling water
Note
Warm water reduces the heating-up time.
Note
Descaling the steam boiler is not required if commer-
cially available distilled water is used.
1. Unscrew the safety lock.
Illustration B
2. Drain the water completely out of the steam boiler.
Illustration P
3. Fill a maximum of 1 l distilled water or tap water into
the steam boiler.
Illustration B
4. Insert the safety lock.
Illustration C
Switching on the device
1. Place the device on a firm surface.
2. Insert the mains plug into a socket.
Press the ON switch.
The LED light is lit in red.
Illustration D
3. When the LED light lights up green, the device is
ready for operation.
Illustration E
4. Press the steam lever.
Illustration F
Steam leaks out.
Regulating the steam volume
The expelled steam volume is regulated using the se-
lector switch for steam volume. The selector switch has
3 positions:
1. Set the selector switch for the steam volume to re-
quired steam volume.
2. Press the steam lever.
3. Before starting cleaning, point the steam gun at a
cloth until steam is expelled evenly.
Refilling water
If the steam volume is reduced during work or if no more
steam volume comes out, the water will have to be re-
filled.
1. Switch the device off; see Chapter Switch off the ap-
pliance.
2. Unscrew the safety lock.
3. Fill a maximum of 1 litre distilled water or tap water
into the steam boiler.
4. Insert the safety lock.
5. Insert the mains plug into a socket.
6. Press the ON switch.
7. Wait until the LED light has changed from red to
green.
The device is ready for use.
Switch off the appliance
1. Press the OFF switch.
2. Pull the mains plug out of the socket.
3. Press the steam lever until no more steam flows out.
Illustration M
The steam boiler is depressurised.
4. Set the child lock (selector switch for steam volume)
to the rear.
The steam lever is locked.
Rinsing out the steam boiler
Rinse the appliance’s steam boiler after max. every
tenth boiler fill.
1. Switch the appliance off, see Chapter Switch off the
applianceSwitch off the appliance.
2. Allow the appliance to cool down.
3. Disconnect the accessory.
4. Fill the steam boiler with water and swing it around
vigorously. Lime residue which has been deposited
on the bottom of the steam boiler will be released as
a result.
5. Drain the water completely out of the steam boiler.
Illustration P
Storing the device
1. Hang the floor nozzle in the park bracket.
Illustration N
2. Wind the steam hose and mains connection around
the carrying handle or device and/or insert the
steam gun in the ground floor nozzle.
Illustration O
3. Insert the extension tube in the large accessory
holder or allow to dry and put in the accessory bag.
Illustration O
4. Allow the rest of the accessories to dry and then
store in the accessory bag.
Illustration O
5. Store the device in a dry location that is protected
from frost.
Important application instructions
Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning
it before using the appliance. In this way the floor will be
cleared of dirt and loose particles before the wet clean-
ing.
Freshening up textiles
Prior to using the appliance, always check the compati-
bility of the textiles at a concealed point: Steam down
the textile, allow it to dry and then check it for any
change in colour or shape.
Cleaning coated or painted surfaces
ATTENTION
Damaged surfaces
Steam can loosen wax, furniture polish, plastic coatings
or paint and edge band from edges.
Do not direct the steam at glued laminated edges as the
edge band may loosen.
Do not use the appliance for cleaning unsealed wood or
parquet floors.
Do not use the appliance for cleaning painted or plastic
coated surfaces such as kitchen or living room furniture,
doors or parquet.
1. To clean these surfaces, steam a cloth briefly and
use it to wipe over the surfaces.
Maximum steam volume
Reduced steam volume
No steam - child lock
Note
In this position, the steam lever cannot
be operated.
