background image

2

Landa ECOS 7000  Operator’s Manual  9.801-316.0 - E

Machine Data Label

Introduction

Thank you for purchasing this Pressure Washer. We reserve the right to make changes at any time

without incurring any obligation.

Owner/User Responsibility:

The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings

before using this pressure washer. Warning information should be emphasized and understood. If the operator is

not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed with the operator

in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its

contents. Owner and/or user must study and maintain for future reference the manufacturers’ instructions.

Save These Instructions

This manual should be considered a permanent part of the machine and should remain with it if machine

is resold. When ordering parts, please specify model and serial number. Use only identical replacement

parts.This machine is to be used only by trained operators.

Notice

This trailer is equipped to meet applicable U.S. Federal safety standards. Check local and state requirements

regarding brakes and any additional equipment that may be required. Any modifications or additions including load 

equalizing hitches, without written factory consent: usage in an abnormal manner including overloading voids all 

manufacturers’ warranties and liability.

WARNING: This Owner's Manual contains safety information and instructions for your trailer.

You must read this manual before loading or towing your trailer.
You must follow all safety precautions and instructions.

Summary of Contents for LANDA ECOS 7000 Series







































Reviews: