Kärcher FC 4-4, Manual

Page: 14 / 48

14 English
몇 CAUTION
Risk of injury
The cleaning rollers start rotating as soon as the device
is switched on. Injuries can occur due to uncontrolled
movement.
Hold the handle tight to prevent the device from moving
away independently.
ATTENTION
Fresh water tank or waste water tank not installed
Material damage
Before starting cleaning work, ensure that the fresh wa-
ter tank is filled with water and the waste water tank is
fitted in the device.
1. Press the ON/OFF switch.
Illustration I
The device switches on.
The cleaning level 1 indicator for normal roller
speed and normal water quantity lights up.
2. Wait until the rollers rotate.
3. Switch to cleaning level 2 using the button for set-
ting the cleaning level.
Illustration J
This increases the roller speed and water quantity.
The Cleaning level 2 indicator lights up.
4. Move the device back and forth until the rollers are
sufficiently moistened.
Note
Selection of cleaning level 1 or cleaning level 2 de-
pends on the type of floor to be cleaned (e.g. wooden or
stone floor).
The device is set to cleaning level 1 after initial start-up.
The cleaning level setting last used always remains ac-
tivated after interrupting and resuming work.
Battery run time
The “Battery” indicator shows the remaining battery run
time:
● 3 LEDs light up - 70% to 100% battery run time
● 2 LEDs light up - 40% to 70% battery run time
● 1 LED lights up - 20% to 40% battery run time
Illustration L
A roller start-stop motion and optical signals warn of a
depleted battery.
● Approx. 5 minutes before the battery is depleted, the
lowest LED flashes and the rollers rotate three times
in the form of a quick start-stop motion.
● All LEDs flash for 30 seconds when the battery is
empty and the device has switched off.
Emptying the waste water tank and refilling
the cleaning fluid
1. Press the ON/OFF switch.
The device switches off.
2. Fix the floor head with the foot and push the handle
forward.
The device stands by itself.
Illustration M
3. Release the waste water tank: Stand with your foot
on the tongue of the waste water tank and push the
handle bar forward.
Illustration N
The waste water tank releases from the device.
4. For draining the waste water tank, do not transport
the waste water tank by the top cover, but hold it lev-
el using both hands.
5. Empty the waste water tank through the openings.
In the case of adhering soiling, remove the cover of
the waste water tank and rinse the waste water tank
with fresh water.
Illustration O
6. Fit the waste water tank (see chapter
Fitting the
waste water tank
).
● If the fresh water tank is empty, the “MIN MAX” indi-
cator (red) lights up.
Illustration K
7. Fill the fresh water tank (see chapter
Filling the
fresh water tank
).
ATTENTION
Danger from escaping water
Risk of damage
Empty the waste water tank every time the fresh water
tank is empty and before filling the fresh water tank to
prevent the waste water tank from overflowing.
Interrupting operation
ATTENTION
Damp rollers
Moisture damage to sensitive floors
Park the device in the parking station during longer work
breaks to prevent damage to sensitive floors through
wet rollers.
1. Press the ON/OFF switch.
The device switches off.
2. Fix the floor head with the foot and push the handle
forward.
The device stands by itself.
Illustration M
3. Park the device on the parking and cleaning station.
Finishing operation
1. Press the ON/OFF switch.
The device switches off.
2. Fix the floor head with the foot and push the handle
forward.
The device stands by itself.
Illustration M
3. Park the device on the parking and cleaning station.
Illustration Y
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device completely after
each application.
4. Clean the device (see chapter
Floor head cleaning
by means of rinsing process
).
Storing the device
ATTENTION
Liquids/moist dirt
Unpleasant odours can develop if the device contains
liquids/moist dirt when stored.
Completely empty the fresh water tank and waste water
tank before storing the device.
Use the cleaning brush to remove hair and dirt particles
from the hair filter in the floor head cover.
Allow the cleaned rollers to dry in the air, e.g. on the
raised elements of the parking station. Do not place the
wet rollers in an enclosed cupboard to dry.
1. Allow the empty waste water tank to dry before fit-
ting it into the device.
2. Park the device on the parking and cleaning station.
Illustration Z
3. Press the handle unlocking button.