P r o g r a m m i n g I o P a s s ™ - S t e p b y S t e p
- P I N E r r o r F u n c t i o n C o n f i g u r a t i o n
25
5.12.2 - Activating the Alarm Relay on Door Ajar
1.
Enter the master password (default is [111111]) fol-
lowed by the [#] key. The LCD displays the follow-
ing:
1. ENROLL
2. PASSWD
3. TIMER
4. SYSTEM
2.
Press [4-System]. The LCD displays:
1.ALARM
2.CHECK
3.MODE
4.OTHER
3.
Press [1-Alarm]. The LCD displays:
1.TAMPER 2.FORCE
3.D_AJAR 4.P_ERR
4.
Press [3-D_Ajar]. The LCD displays:
1.DOOR TIMER
2.ALARM RELAY
5.
Press [2-Alarm Relay] to enable (trigger) or disable
(not trigger) the alarm relay when the door is left
open longer than pre-set time. The LCD displays:
CURRENT: DISABLE
PRESS ’1’ --> CHANGE
6.
Press [1] until desired mode is displayed. Pressing
this key will toggle between selections. When
required mode is displayed, press [#] to save and exit.
5.12.3 - Setting the Door Ajar Timer
The door ajar timer is set to 30 seconds. If the door remains
open longer than 30 seconds, after an “access” event, an
alarm will sound until the door is closed correctly. If
required, you can modify this setting and program a value
between 1-255 seconds.
To set the door ajar timer:
1.
Enter the master password (default is [111111]) fol-
lowed by the [#] key. The LCD displays the follow-
ing:
1. ENROLL
2. PASSWD
3. TIMER
4. SYSTEM
2.
Press [3-Timer]. The LCD displays:
1.STRIKE 2.ALARM
3.DURESS 4.AJAR
3.
Press [4-Ajar]. The LCD displays:
CURRENT: 30 SEC.
NEW:
4.
Using the keypad, enter the number of seconds
during which the alarm will sound. Enter digits in
“seconds”. Press [#] to save and exit.
5.12.4 - Using the Door Ajar Function
Depending if the door ajar function is configured to trigger
the alarm relay, follow this procedure to STOP the warning
device.
1.
When the door is left opened, the alarm relay will be
triggered OR the unit’s piezo will sound. The LCD
will display:
READY FOR CARD
DOOR OPEN
2.
The “Door Open” message is displayed (and
blinking) and will remain on the LCD until the door
is closed properly.
5.13
PIN Error Function Configuration
This function, when enabled, will automatically activate
the “Alarm Relay” when a cardholder keys in his PIN
incorrectly five (5) times consecutively within four (4)
minutes.
Furthermore, the card can automatically be deleted (from
the unit’s memory) when this situation occurs.
NOTE:
This function can only be used when access mode
“1” is used (card and PIN).
5.13.1 - Enabling the PIN Error Function
To enable the PIN error function:
1.
Enter the master password (default is [111111]) fol-
lowed by the [#] key. The LCD displays the follow-
ing:
1. ENROLL
2. PASSWD
3. TIMER
4. SYSTEM
2.
Press [4-System]. The LCD displays:
1.ALARM
2.CHECK
3.MODE
4.OTHER
3.
Press [1-Alarm]. The LCD displays:
1.TAMPER 2.FORCE
3.D_AJAR 4.P_ERR
4.
Press [4-P_Err]. The LCD displays:
CURRENT: DISABLE
PRESS ’1’ --> CHANGE
5.
Press [1] until desired mode is displayed. Pressing
this key will toggle between selections. When
required mode is displayed, press [#] to save and exit.
5.13.2 - Enabling Auto-Deletion on PIN Error
Enable this function if you wish to delete a card from the
unit’s memory when a cardholder enters the PIN
incorrectly five (5) times consecutively within four (4)
minutes.
To enable the auto-deletion feature on PIN error:
1.
Enter the master password (default is [111111]) fol-
lowed by the [#] key. The LCD displays the follow-
ing:
Summary of Contents for IoPass SA-500
