background image

 

 

CDG SERIES LIQUID DISPENSERS 

OPERATORS MANUAL 

Please Read this Manual Now, 

And Retain it for Future Reference  

KanPak CDG Series Liquid Dispensers provides a temperature controlled environment to sustain liquid 
product, such as cream, milk, and other liquids.  The product selections are made by depressing a lever 
to dispense product. The product is stored in the sanitary interior compartment within the dispenser.  
The product (cream, milk, etc.) is prepackaged in a Bag-in-Box. 

Operating the dispenser is a simple two-step process: 

 

1.

 

Place a cup under the product tube. 

2.

 

Push lever down for the desired quantity and product. 

INSPECTION FOR DAMAGE 

When you receive the dispenser, inspect the exterior of the shipping container for damage.  Note any 
damage in detail.  Unpack the dispenser at once (follow the instruction sheet inside the top of the box, 
or see instructions in this manual).  Examine the dispenser for damage.  Report any damage to the 
transportation company immediately.  File a claim for damages promptly.  Your immediate inspection 
protects you against loss since KanPak is not responsible for damages incurred during shipment. 

SAFETY 

KanPak, LLC strives to design robust equipment where safety, simplicity and efficiency are paramount. 
To this effect, the CDG Series has been designed to be low maintenance with a single outside connection 
(electricity). These features are aimed at protecting both operators and technicians. 

This appliance is not to be used by persons (including children) with reduced physical, sensory or mental 
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 
concerning use of the appliance by a person responsible for their safety. 

SAFETY PRECAUTIONS

 

 

Always plug the dispenser into an approved electrical outlet.  

 

Do not touch the dispenser with wet hands.  

 

Unplug the dispenser from its electrical source before servicing.  

 

Do not immerse the dispenser in water. 

 

 

Observe all safety precautions with this dispenser that you would 
with any electrical appliance.  

 

Children should be supervised to ensure that they do not play with 
the appliance.

 

 

Page 1

Summary of Contents for CDG-211





















Reviews: