manualshive.com logo in svg

Kangook Cors-Air Black Bull, User Manual

The Kangook Cors-Air Black Bull is a cutting-edge paramotor that guarantees an exhilarating flying experience. To ensure a seamless and safe operation, we provide a comprehensive User Manual that you can easily download for free from our website. Obtain valuable insights and instructions to maximize your enjoyment of this incredible product.

Share
Download
background image

2 

 

   Kangook Paramotors User Guide –  

 

 

February 2020 – V3.0  

 

        Copyright 2020 All Rights Reserved.   

 

Introduction 

 

To Begin we would first like to thank you for purchasing  a 

Kangook paramotor

. We 

hope  that  our  pursuit  and  desire  for  aviation  innovation  will  make  you  (re)discover 
the joy of a fun 

safe motorised flight

.  

Since 2008 we have been involved in the design, development and  manufacturing 
of a 

wide  

range of modular products.  

Our  paramotor  /  powered  paragliders  (PPG)

s

  are  entirely  manufactured  and 

assembled  in 

Canada

  with  a  continuous  focus  on  premium  quality  and  detailed 

product development.   

 

In this guide you will find all the information concerning the attachment systems, the 
paramotor components, and the precautions to take before enjoying your first flight. 
However  this  document  does  not  replace  the  training  you receive  at  a paramotor 
training centre or your local dealer’s advice. 

Please note that some details or images shown in this guide could be different than 
those corresponding to your equipment.  

If you have any question or comments, do not hesitate to contact us at: 

 

KANGOOK PARAMOTORS

 

 

2699  5e Avenue, Local 20  

Shawinigan, Québec  

G9T 2P7  

Canada  

[email protected]

. 

Tel : 

1-819-538-5000 

Fax : 

418 289 3810

 

Summary of Contents for Cors-Air Black Bull

























































Reviews:

No comments

Related manuals for Cors-Air Black Bull

Brands by name

Popular brands

Load more brands