KAM KCDMIX100
ALL IN ONE CD DJ MIXING SYSTEM
INSTRUCTION MANUAL
www.kam.co.uk
KAM KCDMIX
1
0
0
ALL IN ONE CD DJ MIXING SYSTEM
To use Program
; 1. Press Program button. 2. Use the track
skip buttons to locate the desired track. 3. Press
PROGRAM button again and this selection will be stored so
you can move on to selecting the next track. 4. Press PLAY.
The unit will remain in PROGRAM mode until you either
remove the CD or switch off the power. When PROGRAM
mode is active the LED will light.
o
SEARCH BUTTONS
- use these buttons to listen to music
played at high speed.
1)
JOG WHEEL
- has three Modes.
A.
When playback is paused turning the wheel quickly acts
as an alternative SEARCH method and plays the currently
selected track at high speed.
B.
When playback is paused turning the wheel slowly moves
the currently selected Cue Point in either direction one
frame at a time. When you have found the correct Cue
Point, pressing PLAY assigns the Cue Point to the
CUE BUTTON.
C.
When a track is playing the wheel acts as a momentary
Pitch change method. The amount of pitch change is
determined by the speed of rotation.
1!
PLAY/PAUSE
- Each press of the PLAY/PAUSE button
causes the operation to change from play to pause or from
pause to play.
1@
CUE
- Pressing the CUE button during playback provides
a return to the Cue Point from which play was started. To
adjust the Cue Point pause playback, use the JOG WHEEL
to locate the desired new Cue Point and press PLAY.
1#
BOP BUTTON
- Pressing this button at any time will cause
playback to start from the currently selected main Cue
Point.
1$
PITCH BUTTON
- turns the Pitch control system on & off.
1%
PITCH RANGE
- Press to select the pitch range of the
PITCH SLIDER. The two LEDs will show the currently
selected pitch range (+/- 8% or +/- 16%).
1^
PITCH SLIDER
- adjusts the Track Playback speed by up to
+/-16% (depending upon the settings selected via the
PITCH RANGE BUTTON).
1&
PITCH BEND BUTTONS
- track playback speed will be
adjusted by +/-16% for as long as you hold down one of
these buttons.
1*
SEAMLESS LOOP SECTION
- You can create two seamless
Loops of any sections of audio from a CD. Each seamless
Loop facility has identical controls. To create a Loop;
1. Identify a section of a track you wish to Loop and pause
playback a few seconds before the section starts.
2. Press play. 3. Press BUTTON ‘A’ at the precise moment
you wish to be the start of your Loop. 4. Press the B
LOOP/EXIT BUTTON at the precise moment you wish to be
the end of your Loop. 5. Your Loop should now play
continuously. 6. To exit the Loop and return to normal CD
playback press the B LOOP/EXIT BUTTON again. 7. You can
jump straight back to playing your Loop again at any time by
pressing the RELOOP BUTTON.
MIXER FEATURES
1(
CHANNEL SELECTORS
- this is a 5 input mixer. Both the
music channels can be set to carry the sound from the
integral CD players or from the rear panel inputs (that can
be set to accept either Line or Phono level signals). This
switch is used to choose between either the integral CD
players or the external Line/Phono rear panel input on each
channel.
2)
GAIN CONTROLS
- adjust the channel input levels allowing
the user to reduce or increase the sound level to
compensate for quiet recordings. NOTE: care should be
taken not to produce distortion with these controls.
2!
EQ CONTROLS
- used to cut and boost specific
frequencies within your music. Turning the control clockwise
boosts the frequency. Turning the control anti-clockwise
reduces the frequency. The BASS control alters the level of
Bass frequencies, MIDDLE alters the mid frequencies, the
TREBLE alters high frequencies.
2@
CHANNEL LEVEL FADERS
- used to adjust the output level
for each channel. NOTE: care should be taken not to
produce distortion with these controls.
2#
MIC SWITCH
- this three position switch is used to to
turn the microphone off, on or engage the Talkover Facility.
Talkover automatically reduces the music level while the
microphone is in use and then automatically returns the
music to normal level when the microphone is no longer
in use.
2$
MIC LEVEL
- used to set the volume of the Microphone.
2%
MIC EQ
- The MC/DJ microphone has its own dedicated
BASS and TREBLE EQ controls. NOTE: To maximize the
performance of this microphone channel check out the
range of Mixer Matched KAM Microphones.
2^
SPLIT / MIX SWITCH
- controls the way in which the
headphone monitoring circuit works. In the SPLIT position
the sound from channel 1 is played on one side of the
headphones and the audio from channel 2 on the other.
When the switch is in the MIX position the sound from
both channels is heard in both sides of your headphones.
2&
CUE MONITOR SELECT FADER
- controls what is
monitored in the headphones. With the fader to the left
you should hear the sound from channel 1 only. With the
fader to the right you should hear the sound from channel
2 only. With the fader in the centre you should hear a mix
of both channels 1 and 2.
2*
KAM PROFADE CROSSFADER
- allows the user to mix
smoothly between both music channels.
2(
CUE LEVEL
- controls the output volume of the
headphones. Care should be taken not to have this set to
high as it could result in damage to both the hearing of
the user and the headphones. The channel to be
monitored is selected via the cue monitor select fader.
3)
LED LEVEL DISPLAY’S
The unit has two LED level displays. They show the Left
and Right levels of the Master Output of the mixer.
3!
MASTER OUTPUT CONTROL
- controls the overall output
level from the mixer, from the master output to the PA
System. NOTE: care should be taken not to produce
distortion with these controls as this could result in
damage to both the unit and any external equipment
connected.
© COPYRIGHT LAMBA plc 2005. E&O E.
OVERVIEW
The KCDMix100 has been designed to give the
aspiring DJ all of the facilities you need to learn and
develop the skills you need to become a CD DJ.
It provides two identical CD player units and a built in
two c mic channel DJ mixer.
CD PLAYER FEATURE DETAILS
q
LCD DISPLAY
- provides visual information regarding
current settings.
w
EJECT
- opens and closes the CD TRAY. NOTE: the
tray will not open when a disc is playing.
e
TRACK SKIP
- standard Track Skip buttons.
r
+10 BUTTON
- is essentially a TRACK SKIP button
that jumps forward ten tracks at a time.
t
TIME/STOP BUTTON
- switches the screen between
showing Elapsed or Remaining time for an individual
track or the entire CD. Press and hold for 3 seconds
to place the unit in ‘stop’ mode.
y
CUE/SINGLE/CONTINUE
- switches between
standard CONTINUE mode where each track on a
CD will be played in turn... and AUTO CUE SINGLE
mode where when a track finishes, playback will stop
and the beginning of the next track will be Cued ready
for playback.
u
RELAY
- In Single Mode RELAY causes each CD
player to play individual tracks, back to back in relay. In
Continuous Mode each CD will be played in turn until
playback is stopped.
i
PROGRAM
- You can use this facility to program up
to 28 tracks to play in your chosen order.
SPECIFICATION
Mixer Audio Inputs
2 x CD + 2 x Line + 2 x Phono + 1 x Mic
Audio Output
Unbalanced line level RCA
Digital Output
RCA coaxial S/PDIF
Output
Master / Record / Headphone
Channel EQ
3 band per channel
Microphone EQ
2 band
Microphone Talkover
Yes
Metering
Stereo 10 band LED
Monitor
Split cue headphone monitoring
Disc Input
Top loading
Pitch Range
+/-16%
Anti-Shock
Yes
LEDs
Blue
Seamless Loop
Yes
Instant Cue
Yes
Programmable Tracks
Up to 28
Crossfader
User replaceable
Due to continuous product development, specifications are subject to change.
If this product is ever no longer functional please it take to
a recycling plant for environmentally friendly disposal.
REAR PANEL CONNECTIONS
3@
MAINS POWER SWITCH
3#
INPUTS
- each channel features RCA type inputs which are
switchable between Line Level (for CDs etc) and Phono Level (for
decks) connections. NOTE: always use shielded signal cables to
reduce hum and background noise. The unit should always be
switched off when connecting cables.
3$
INPUT SELECTION SWITCHES
- use these switches to choose
which signal type is selected for the inputs.
3%
GROUND POSTS
- when using the Phono Level selection to
attach a turntable use these to attach the ground wires from
turntables.
3^
ANALOGUE AUDIO OUTPUTS
- the unit has two outputs. The
MASTER (unbalanced Line level) is usually used to connect the
KCDMIX100 to your amplifier. The RECORD (unbalanced Line
level) is usually used to connect the KCDMIX100 to the line input
of your tape deck or MD so that your can record your
performance.
3&
DIGITAL AUDIO OUTPUTS
- use these S/PDIF RCA output
connections to connect each CD Player to the input of a suitably
equipped Digital Amplifier or the Audio Interface of a Computer.
LEFT
RIGHT
MASTER
RECORD
DIGITAL
OUTPUT
AUDIO OUTPUTS
CHANNEL 2
LINE
PHONO
LINE
PHONO
CHANNEL 1
AUDIO INPUTS
CD2
DIGITAL
OUTPUT
ON
OFF
CD1
POWER
KCDMIX100
TWIN DESKTOP CD PLAYERS
& MIXER UNIT
WWW.KAM.CO.UK
MADE IN CHINA
CD PLAYER 1
CD PLAYER 2
LINE/
PHONO
OFF
TALK
OVER
ON
CD1
CH1
CH2
SPLIT
MIX
LINE/
PHONO
CD2
CD1
TREBLE
-15
+
15
CD1
MIDDLE
-15
+
15
CD1
BASS
-15
+
15
MIC
LEVEL
0
10
MIC
TREBLE
-
+
MIC
BASS
-
+
CD1
GAIN
0
10
CD2
TREBLE
-15
+
15
CD2
MIDDLE
-15
+
15
CD2
BASS
-15
+
15
CD2
GAIN
0
10
CUE
LEVEL
0
10
MASTER
0
10
12
KHz
2.5
KHz
80
Hz
CHANNEL 1
C R O S S F A D E R
LEFT
RIGHT
CHANNEL 2
CD 1
CD2
TRACK SKIP
A
B/LOOP
EXIT
RELOOP
AUTO-
CUE
SING/
CONT
TIME-/
STOP--
PROG
PITCH
PITCH BEND
RELAY
PITCH
ON/OFF
8%
16%
RELOOP
B/LOOP
EXIT
SEARCH
BOP
BPM
A
PITCH
CONTROL
SPEED
CD 1
TRACK SKIP
A
B/LOOP
EXIT
RELOOP
AUTO-
CUE
SING/
CONT
TIME-/
STOP--
PROG
PITCH
PITCH BEND
PITCH
ON/OFF
8%
16%
RELOOP
B/LOOP
EXIT
SEARCH
BOP
BPM
A
PITCH
CONTROL
SPEED
CD 2
KCDMIX100
KCDMIX100
KCDMIX
10
0
KCDMIX
10
0
q
q
w
w
e
e
r
r
t
t
y
y
u
i
i
o
o
1)
1)
1!
1@
1#
1!
1@
1#
1$
1$
1%
1%
1^
1^
1&
1&
1*
1*
1(
2)
2!
2!
2@
2#
2$
2%
2^
2&
2*
2(
3)
3!
3@
3#
3$
3%
3^
3&
