Kalkhoff Derby Cycle Werke GmbH 2011 User Manual Download Page 122 | Manualshive

Page: 122 / 384

background image

III User Manual Pedelec with centre motor

25

8.1.2.3 Display "E1"

If "E1" is displayed, the following cause/solution may
apply:

Error code

›

You have pushed down on the pedals shortly after
pressing the "Power" button. Switch the display off
then switch it back on and do not push down on the
pedals for roughly 2 seconds.

If "E1" is displayed the distance covered will not be
recorded. It will therefore no longer be possible to
adjust the assistance control and the power assist
will no longer work.

8.1.2.4 Display "E9"

If "

E9

" is displayed, the following cause/solution may

apply:

Error code

›

A problem occurred with the drive unit. Contact
your specialist cycle shop if this occurs.

If "E9" is displayed the distance covered will not
be recorded. It will therefore no longer be possible
to adjust the assistance control and the power as-
sist will no longer work.

8.1.2 Pedelec with LCD control panel

8.1.2.1 No display

If nothing is shown in the LCD display, one of the follow-
ing reasons/solutions may apply:

›

Is the battery sufficiently charged?
Charge the battery.

›

Is the battery capacity still sufficient?
Check the capacity. If the remaining capacity is not
enough, the battery must be replaced.

Check the actual battery capacity

If you press the "Push" button for longer than five sec-
onds, the LEDs show the capacity of the battery at present.

Capacity of 18 Ah battery (example)

DISPLAY

CAPACITY

5 LEDs light up •••••

100 – 80%

4 LEDs light up ••••

80 – 60%

3 LEDs light up •••

60 – 40%

2 LEDs light up ••

40 – 20%

1 LED lights up •

20 – 0%

8.1.2.2 Battery charge state indicator flashing or not visible

If the battery charge state indicator is flashing or not visi-
ble at all, one of the following causes/solutions may apply:

›

Is the battery sufficiently charged?
Charge the battery if necessary.

›

The second and fourth LEDs of the battery indicator
flash when you press the button on the battery. The
battery management has switched the battery off.
Put the battery in the charger and charge it.

›

If you continue to press the button on the battery
(test for battery capacity) and no LED lights up, the
battery management has switched the battery off.
Put the battery in the charger and charge it.

«
...
120
121
122
123
124
...
»

Summary of Contents for Derby Cycle Werke GmbH 2011

































































































































































































































































































































































































Reviews:

No comments

Related manuals for Derby Cycle Werke GmbH 2011

Brand: Scott Pages: 5

Brand: Cannondale Pages: 22

Brand: Bell Pages: 32

Brand: Giant Pages: 1

Brand: Puky Pages: 36

Brand: Huffy Pages: 32

Brand: Omcan Pages: 12

Speedbike Standard

Brand: Alois Praschberger Pages: 4

Brand: Kidzmotion Pages: 9

Brand: CRUZBIKE Pages: 11

Urban iki Ta-ke

Brand: OGK Pages: 60

Brand: Cateye Pages: 1

Brand: MBM Pages: 40

Brand: Siemens Pages: 160

Brand: Siemens Pages: 172

COMFORT CRUISER

Brand: Pedego Pages: 12

Brand: Gazelle Pages: 480

M1-ERZBERG Pedelec

Brand: M1-Sporttechnik Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands