Kalkhoff Bosch Cruise User Manual Download Page 264 | Manualshive

Page: 264 / 550

background image

28

VIII User Manual Pedelec Xion

If used incorrectly, the device may be damaged or
inflict injuries.

›

Before cleaning the charger, always pull the plug
out of the socket to avoid a short-circuit and/or
physical injury.

›

Only use the charger in dry rooms.

›

Only place the charger in a secure stable position
on a suitable surface.

›

Do not cover the charger or place any objects on
it as otherwise it could overheat and catch fire.

8 Charger

Read the type plates on the charger before using it for the
first time.

You can charge your Pedelec with Xion drive directly via a
charging socket in the battery. The battery can remain on
the Pedelec whilst the charging operation is in progress.

Alternatively, you can take the battery out of its holder
and charge it elsewhere.
This is recommended if it is cold outside, in order to
charge the battery in a warmer room. The battery can be
charged at temperatures between 0°C and 45°C.

Do not use other chargers. Only charge the battery us-
ing the charger provided, or a charger approved by us.

•

If a charging fault occurs, the LED in the charger
flashes red. In this case, the charging current is too
high.

•

Disconnect the battery from the charger and then
connect it again. If the error message still appears,
the battery and charger must be checked by a spe-
cialist dealer.

Charging the battery

«
...
262
263
264
265
266
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

CYCLO 315 Series

Brand: Magellan Pages: 39

Brand: Fenix Pages: 4

RockShox SEKTOR

Brand: SRAM Pages: 49

Brand: Air Bike Pages: 8

STREET RAMP L1 EXTENSION

Brand: SENDER RAMPS Pages: 21

Brand: Ciclo Pages: 8

Brand: Scott Pages: 16

Brand: wayscral Pages: 60

Brand: UNIPRODO Pages: 17

Brand: Gazelle Pages: 438

Brand: Hase Spezialräder Pages: 28

Brand: Canyon Pages: 36

Brand: hepco & becker Pages: 4

Brand: Grace Pages: 63

Brand: SoFlow Pages: 7

Brand: VDO Cyclecomputing Pages: 87

Brand: PIHSIANG MACHINERY Pages: 20

Brand: A/O Bicycle Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands