manualshive.com logo in svg

Kalkhoff Bosch Cruise, User Manual

The Kalkhoff Bosch Cruise electric bicycle is a stylish and efficient mode of transportation. To fully enjoy its features and functions, make sure to download the User Manual for free from our website. Discover how to maximize your riding experience and navigate any situation effortlessly with this comprehensive manual.

Share
Download
background image

14 

 

III User Manual Pedelec with centre motor

4.2.1   Function of LCD control panel

4.2.1.1   On / Off button

Press the "On / Off" button to switch on the control panel 
and drive.

The assist level that was active at the time the control 
panel was switched off is automatically reinstated. The 
back-lit display is turned on briefly then goes out. All 
recording of data (trip, actual journey length, average 
speed, top speed, total journey length) starts as soon 
as you switch the control panel on and stops when you 
switch it off.

4.2.1.2   Selector button for display panel 

You can display the information "Trip", "Average speed", 
"Top speed" and "Total journey length" consecutively 
by pressing the selector button for the display panel 
("Mode").

The setting that was selected when you switched off is 
also displayed first in this case.

4.2.1.3   Changing the assist level

Increase power assist

The following assist levels are displayed one by one when 
you press the button that increases the assist level: 

"NO 

ASSIST / no assistance"

, 

"ECO / low assist level"

, 

"STAND-

ARD / medium assist level"

, 

"HIGH / high assist level"

, fol-

lowed once again by 

"NO ASSIST / no assistance"

. This 

means that the amount of assistance increases each time 
you press the button until you reach the highest level. If 
you subsequently press the button, the assistance switch-
es off.

Reduce power assist

If you press the button that reduces the assist level, the 
assistance reduces each time the button is pressed and 
returns to the most powerful assist level when it reaches 
the end of the loop. 

In the 

"NO ASSIST / no assistance"

 mode, you ride the bike 

normally without the assistance of the motor.

4.2.1.4   Resetting recorded data

If you press the selector button for the display panel for 
longer than three seconds with the control panel switched 
on, this resets the trip, average speed and top speed read-
ings to zero. You cannot delete the total journey length 
using this method.

4.2.1.5   Switching the display on and off

The back-lit display and LCD control panel display can 
also be switched on even if the drive is not enabled. To 
do this, press the button that switches the lights on. The 
drive remains in "

NO ASSIST / no assistance" mode

. Now 

you cannot change the assist level. 

If you press the light button when the control panel is 
switched on, the back-lit display turns on.

If you press the light button when the light is on, the back-
lit display turns off. The power assist is still available and 
you can change the assist level.

4.2.1.6   Deleting all data

Press the display ("Mode") selector button and the button 
that deletes all data on the rear of the control panel at the 
same time to delete all the data stored, including the total 
journey length. The display then automatically switches 
to settings mode for language, LCD contrast and wheel 
circumference.

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Cane Creek EC Installation Manuals preview
EC
Brand: Cane Creek Pages: 2
Surly Dummy Instructions preview
Dummy
Brand: Surly Pages: 2
FOX RACING SHOX FLOAT 100R Owner'S Manual preview
FLOAT 100R
Brand: FOX RACING SHOX Pages: 16
Vanraam Fun-2-Go User Manual preview
Fun-2-Go
Brand: Vanraam Pages: 43
Playskool 1-2-3 Bike Instructions preview
1-2-3 Bike
Brand: Playskool Pages: 4
VARUN C20-1 White User Manual preview
C20-1 White
Brand: VARUN Pages: 84
Yedoo Mezeq disc User Manual preview
Mezeq disc
Brand: Yedoo Pages: 37
MBM PRIMAVERA 28 User Manual preview
PRIMAVERA 28
Brand: MBM Pages: 40
Ice Bear PST300C Manual preview
PST300C
Brand: Ice Bear Pages: 42
Woom 2 Manual preview
2
Brand: Woom Pages: 8
Brenter Snowbike C4 Owner'S Manual preview
Snowbike C4
Brand: Brenter Pages: 12
Lupine Wilma R Manual preview
Wilma R
Brand: Lupine Pages: 23
Hauck Prema Instructions Manual preview
Prema
Brand: Hauck Pages: 28
Electric Bike Technologies FAT TRIKE Owner'S Manual preview
FAT TRIKE
Brand: Electric Bike Technologies Pages: 55
Mactronic BATTERY SCREAM 3.3 Quick Start Manual preview
BATTERY SCREAM 3.3
Brand: Mactronic Pages: 2
Kinderkraft ASTON User Manual preview
ASTON
Brand: Kinderkraft Pages: 52
Marzocchi Z2 Alloy 1999 Owner'S Manual preview
Z2 Alloy 1999
Brand: Marzocchi Pages: 25
Decathlon ONE SECOND CLIP Quick Start Manual preview
ONE SECOND CLIP
Brand: Decathlon Pages: 2

Brands by name

Popular brands

Load more brands