KAESER EPC 1500-G Assembly And Operating Manual Download Page 46

Page: 46 / 102

6.2 Reporting Transport Damage

1. Check the machine for visible and hidden transport damage.
2. Inform the carrier and the manufacturer in writing of any damage without delay.

6.3 Fitting the rubber pads

CAUTION

There is a danger of tilting because of the high centre of gravity and mass of the machine.
➤ Use transport slings to lift the machine.

Fig. 10 Fitting the rubber pads

Rubber pad

Hexagonal nut

➤ Remove the wooden frame from the base plate.
➤ Fit the rubber pads to the base plate with hexagon nuts.

6.4 Replacing the air filter

➤ Mount the air filter before commissioning.
The inlet opening in the filter must face downwards.

Fig. 11 Replacing the air filter

Air filter

➤ Fit the supplied air filter (depending on machine).

Result The machine is ready for operation.

Installation

6.2

Reporting Transport Damage

Assembly and operating manual 1-stage piston compressor
EPC-G

No.: 9_5752 24 E

Summary of Contents for EPC 1500-G







































































































Search results

Summary of Contents for EPC 1500-G

Reviews:

Related manuals for EPC 1500-G

Brands by name

Popular brands

KAESER EPC 1500-G, Assembly And Operating Manual

Search results

Summary of Contents for EPC 1500-G

Reviews:

Related manuals for EPC 1500-G

Brands by name

Popular brands