K-Tool KTI-63105A Owner'S Manual Download Page 1 | Manualshive

Page: 1 / 8

K-Tool KTI-63105A Owner'S Manual Download Page 1

KTI-63105A

1

2 TON EXTRA LONG LOW PROFILE SERVICE JACK

OWNER'S MANUAL

KTI-63105A

SPECIFICATIONS

Capacity ............................................................................... 2 Ton

Low Height ............................................................................ 2-3/4"
High Height .............................................................................. 24"
Pump Stroked to Load ............................................................... 8
Chassis Length ....................................................................33-7/10"
Low Clearance Length .............................................................15"
Overall Width ........................................................................ 14-3/5"
Chassis Height ....................................................................... 5-1/2"
Handle Length .................................................................... 49-1/5"
Saddle Diameter .....................................................................3-9/10"
Net Weight .....................................................................100.94 lbs.
Gross Weight .....................................................................105.8 lbs.

www.P65Warnings.ca.gov

Cancer and Reproductive Harm-

WARNING:

Complies with ASME PASE/2014 Safety Standard

1
2
3
...
»

Summary of Contents for KTI-63105A









Reviews:

No comments