LCD touch control
1. Power: When power-on ,the backlight is lit .then showing the
“
24-hour system
”
,the output is off,
and the machine standby .Without any operation, the backlight disappear automatically after 30
seconds.
2.
“
Light
”
key: Press that key once, the lamp and the
is lit. Press the key once more, the
light of the lamp and
will be disappear, and it is a circulation of this operation.
3. The Add key
“
”
, also the switch that control power-on. The motor has three speed :low
﹑
medium
﹑
high.
①
.Press the key
once ,the
is displayed on the screen ,and the motor work,
means low speed(the switch that control power-on.)
②
.Press the key
when at the low speed .the
will be displayed on the screen,
means medium speed.
③
.When it is at the medium speed ,press the key
again. The
will be
displayed on the screen ,
means at high speed.
④
.Press the key
once more at the high speed, the
still on the screen ,the
motor work normally ,the machine still at high speed.
4. The Dec key
“
”
,also the switch that control the power-off
①
.Press the
“
”
key once ,the motor shifts down one level, and the a peed will be
displayed on the screen at the same time; Continually press the Dec key till the machine at
no speed, the switch control power-off(the motor stop working).
5. Timer key
“
”
:
1.the timer key is used to setting time, when the speed and lamp don’t work.
○
1 .Long press timer key
for 2-3 seconds, time segment
,and the first two
number for hour setting will flash. The
is used to increase the number, and the
is
used to decrease. Namely: The variability is 01 each time when it is pressed once. And the
largest digit is 23.the
key can’t work when exceeded. If it is equal to 00,the
key can’t
work.
○
2 .Press the timer key
for the second time. time segment
,and the last two
number for minute setting will flash. Then the
key is used to increase the digit, the
key
is used to decrease. Namely: The variability is 01 each time when it is pressed. The largest
digit is 59.And the
key can’t work when exceeded, If it is equal to 00,the
key can’t work.
○
3 Press the timer key
for the third time, and it means time setting exit and
confirmation.
○
4 Long press the timer key
for 2-3 second under this mode, it is for the hour
setting.Press it for the second time:minute setting.Press it for the third:time setting exit and
confirmation.And when it is pressded,it will repeat the action again and again(It can’t run this
procedure,if the first time pressing doesn’t exceed 2 seconds)
2.The timer key is used for timing setting,when the motor or lamps are working.
○
1 .There are three periods of time:5min
﹑
15min
﹑
30min and cancel timing .First time
setting is 5min,Second time setting is 15min,the third setting is 30min,and the forth pressing
is for cancelling.The fifth is 5min,the sixth is 15min.Then repeated again and again.
○
2 .eg:Let the setting be 15min,then the display is 00:15
﹑
00:14
﹑
……00:01,00:00,per
minute display.Once the
“
00:00
”
displayed.the motor and the lamps’ power will be cut off
automatically,(the
“
24-hour systme
”
is displayed on the screen,and the output is off.The
machine standby,and the backlight will disappear automatically after 30 seconds.)
○
3 .Shifting the time segment,it start to decrease gradually after 5 seconds.(eg:the 15min
shift to 30min,5 seconds delay,00:30 will be decrease gradually on the screen.)
