background image

Dewert User Manual Heavy-Weight Tables – Updated 11.2021/3 MDR                                                         Page 11 of 14 

8. Reporting obligation 

All serious incidents occurring in connection with the product shall be reported to the manufacturer (

K.H. 

Dewert GmbH

) and to the 

competent authority

 of the Member State in which the user and/or the patient 

resides. 

Member State 

Competent authority 

Web 

Estonia 

Health Board 
Terviseamet 

https://www.terviseamet.ee/en 

Finland 

Fimea 

https://www.fimea.fi/web/en 

Iceland  

Iceland Medicines 
Agency 

https://www.ima.is/ 

Luxembourg 

CNS 

https://cns.public.lu/en 

Malta 

MCCAA 

https://mccaa.org.mt/ 

Switzerland 

Swiss medic 

https://www.swissmedic.ch/swissmedic/de/home.html 

A serious incident is an incident that directly or indirectly had, could have had, or may have had any of the 
following consequences:  

 

death of a patient, user or other person,  

 

temporary or permanent serious deterioration of the state of health of a patient, user or other person,  

 

serious threat to public health. 
 

9. Disposal 

 

 

 

Packaging 

 

Safety notice: Pay attention to sharp edges and pointed objects during disposal! 
 

The packaging materials produced are mainly: 

o

  Cardboard/Paper 

o

  Plastic 

o

  Wood (when delivered on a pallet) 

 

Please observe the local regulations for waste disposal and preferably recycle the materials. 

As a manufacturer, we are licensed as a participant in the Dual System in accordance with the German 
Packaging Act (VerpackG) and therefore bear the disposal costs, meaning you can dispose of the packaging 
free of charge.   

 

Product 

 

Safety notices: 

o

  Pay attention to sharp edges and pointed objects! 

o

  When transporting the table, only take hold of the underframe, 

NOT

 the upper frame. 

o

  In order to prevent accidents later on, the no longer used product must be rendered unusable 

immediately, e.g. by disconnecting the power cable. 
 

Please observe the local regulations for waste disposal and preferably recycle the materials. 
Tables with electromotive height adjustment are subject to WEEE Directive 2012/19/EU. These old devices 
must be collected, recycled and disposed of in an environmentally sound manner. Use the return and 
collection systems available to you for this purpose. 
 
 
 
 
 

Summary of Contents for 208















Reviews: