JYE Tech WAVE2 Quick Start Manual Download Page 1

Page: 1 / 2

JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2

WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH

QUICK START GUIDE

(REV. 4)

WAVE2 OSCILLOSCOPE

WA E

Basic Operations

CONTROL

POWER ON / OFF

To Power ON

Press the Adjustment Dial.

To Power OFF

Press and Hold the Adj. Dial for 2 seconds, or

press the Adj. Dial to bring up Menu and select

“PWR OFF”.

BATTERY SWITCH

When battery is installed, set the battery switch to ON position.

Toggle between OFF and ON positions to hard-reset the WAVE2

when battery powered.

AUXILIARY PORT PINOUT

MAIN MENU

Press the Adj. Dial at any time to enter the main menu.

ClrOffset

Measure

Send Data*

Default

WF Memory

Sig. Gen

Auto Off

Y-T / Y-X

Info

STB

Pers.

ESC

REBOOT

PWR OFF

Align Vertical Position (VPos)

indicators to 0V

Enter measurement selection menu

Send captured data via serial port

Restore factory default settings

Enter waveform save/recall menu

Enter Signal Generator mode

Enter Auto Power-Off menu

Enter Y-T / Y-X plotting mode

Display WAVE2 firmware details

Toggle Slow Time Base (50ms/div or

slower) mode between ROLL / SCAN

Toggle trace persistence ON / OFF

Exit Menu

Reboot

Power off

Exit

Select

Prev/Next

Select

MEASUREMENTS

*COM Port Settings: Data Bits: 8, Parity: None, Stop Bits: 1, Baud Rate: 115200 bps

Select the waveform parameters to be displayed on screen.

Vmax

Vmin

Vavr

Vpp

Vrms

Freq

Cycl

Duty

10x

ESC

Maximum voltage of signal

Minimum voltage of signal

Average voltage of signal

Peak-to-Peak voltage of signal

Root-Mean-Squared (RMS) voltage

of signal

Most prominent Frequency of signal

Most prominent Wavelength of signal

Most prominent Duty Cycle of signal

Select to auto-correct signal when

10x probe is used

Return to main menu

Exit

Select

Prev/Next

Select

WAVEFORM MEMORY

Select the memory for waveform to be saved or loaded.

Mem 1 - 4

ESC

Save

Load

Memory blocks 1 through 4

Return to main menu

Save the last displayed waveform to

selected memory and return to the

state before entering main menu

Load waveform from selected

memory. The loaded waveform is

displayed in HOLD state

Exit

Select

Prev/Next

Select

AUTO POWER-OFF TIME

(only enabled when the WAVE2 is running on battery and not connected to external power)

Select the Auto Power-Off time when the oscilloscope will turn off during

periods of inactivity.

User

Never

ESC

Customize auto power-off time

Disable auto power-off

Return to main menu without saving

Confirm and exit

Exit

Select

Prev/Next,

Adjust time

(User mode)

Select

Multi-function buttons

F1 through F4

Adjustment (Adj.) Dial

Battery Switch

Power supply input (USB)

CH1 (Y) signal input

Test signal terminal

CH2 (X) signal input

Auxiliary port

GND

Serial port signal RX1 (input)

Function generator signal B (output)

GND

+3.3V (power)

Function generator signal A (output)

BOOT 0

BOOT 1

External trigger signal (input)

(0 - 10V level range)

Trigout (output)

PCB REVISION

FIRMWARE VERSION

109-15800-00J OR LATER

113-15801-091 OR LATER

WHAT’S INCLUDED

WAVE2 Dual Channel Oscilloscope

BNC Probes (x2)

USB Power Cable

Quick Start Guide

Assembly Guide

(included with 15801K only)

ON OFF

Serial port signal TX1 (output)

VRAW

*Trigout is a 3.3V negative going pulses that marks the moment of trigger. The low level

width varies depending on timebase setting.

Summary of Contents for WAVE2

Page 1: ...H WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JY...

Page 2: ...AVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETECH WAVE2 JYETE...

Search results

Summary of Contents for WAVE2

Reviews:

Related manuals for WAVE2

Brands by name

Popular brands

JYE Tech WAVE2, Quick Start Manual

Search results

Summary of Contents for WAVE2

Reviews:

Related manuals for WAVE2

Brands by name

Popular brands