JVL MIS17 Series User Manual Download Page 163 | Manualshive

Page: 163 / 367

background image

JVL Industri Elektronik A/S - User Manual - Integrated Stepper Motors MIS17x, 23x, 34x, 43x

163

Zero search modes

Zero point offset Example.

Setup done before start:

- Zero search velocity = -128 rpm

- Zero search position = - 10000 counts

6.5.9

Setting up zero search without MacTalk

If MacTalk is not used for setting up parameters/registers related to the zero search fea-

ture it must be done as follows.

The motor contains a number of registers which can be accessed from various protocols

depending at which options the motor has.

Protocols available are for example Ethernet (EthernetIP, PROFINET etc.) and CAN-

open, Modbus or the MacTalk protocol.

Each field in MacTalk described earlier in this chapter is accessing a register in the motor.

The registers that are relevant for zero search operation are:

Zero search basic settings:

R38

P_HOME

MacTalk name: “Zero search position”

The found zero point is offset with this value.

See also

R40

V_HOME

MacTalk name: “Zero search velocity”

The velocity to use during zero search.

Set a negative velocity to search in the negative direction.

See also

R41

T_HOME

MacTalk name: "Zero search torque (0-100%)"

The measured torque where the zero search must end.

R42

HOMEMODE

MacTalk name: “Zero search mode”

Selects the zero search type that should start on power up.

See also

TT2192-02GB

The motor moves in negative

direction with 128 RPM defined by
«

» setting

Zero search velocity

Step 1

Step 2

START

The motor moves in positive direction with 2 RPM which is
1/64 of the defined «Zero Search Velicity» and the actual
position counter is set to the «Zero Search position» which
is -10000 count..

Zero search sensor

Position before zero search
(“Sensor Type 2”)

Motor decelerate and stops behind the sensor

Step 3

The motor is set back in the selected «Start up mode» which
in this example is «Position mode». Since the target position
is default 0 it moves to position 0 and stops. The zero search
is finished !

«
...
161
162
163
164
165
...
»

Summary of Contents for MIS17 Series
















































































































































































































































































































































































Reviews:

No comments

Related manuals for MIS17 Series

Brand: Waldbeck Pages: 72

Brand: Polini Pages: 32

MULTI-VANE 1800 Series

Brand: Ingersoll-Rand Pages: 12

Brand: Ridder Pages: 16

Brand: Power Fist Pages: 40

Brand: REXROTH Pages: 86

Brand: SOMFY Pages: 48

SIMOTICS SD 1LE8 Series

Brand: Siemens Pages: 29

SIMOTICS M-1PH1

Brand: Siemens Pages: 8

Simotics SD 1LE7

Brand: Siemens Pages: 44

SIMOTICS S-1FT2

Brand: Siemens Pages: 102

SIMOTICS T-1FW4407-1KM81-1BC0-Z

Brand: Siemens Pages: 114

SIMOTICS S-1FK7 DYA Generation 2

Brand: Siemens Pages: 104

SIMOTICS SD SH 71 315 Series

Brand: Siemens Pages: 132

SIMOTICS SD 1LE5

Brand: Siemens Pages: 136

SIMOTICS S-1FK7

Brand: Siemens Pages: 134

SIMOTICS M-1PH1

Brand: Siemens Pages: 134

Simotics M-1FE1 Series

Brand: Siemens Pages: 150

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands