JVC UX-S77 Page 19 Service Manual Download

Page: 19 / 83

(No.MB230)1-19

3.2.2 Removing the DVD servo board

(See Figs.6 to 8)

Caution:

Solder the short land sections

on the DVD pickup before dis-

connecting the card wire extending from the DVD pickup. If
you do not follow this instruction, the DVD pickup may be dam-
aged.
(1) From the topside of the DVD changer mechanism assem-

bly, solder the short land sections

on the DVD pick up.

(See Fig.6.)

(2) From the bottom side of the DVD changer mechanism as-

sembly, disconnect the card wire from the connectors
(

CN201

CN451

) on the DVD servo board. (See Fig.7.)

(3) Disconnect the wires from the connectors (

CN452

CN453

)

on the DVD servo board. (See Fig.7.)

(4) Remove the screw

attaching the earth wire. (See Fig.7.)

Reference:

After attaching the earth wire, fix it with the spacer as be-
fore. (See Fig.7.)

(5) Remove the two screws

attaching the DVD servo board.

(See Fig.7.)

(6) From the reverse side of the DVD servo board, release the

lock of the connector

CN101

in the direction of the arrow

and disconnect the card wire. (See Fig.8.)

Caution:

Unsolder the solders from the short land sections

after reas-

sembling. (See Fig.6.)

3.2.3 Removing the switch board

(See Fig.7)

• Prior to performing the following procedures, remove the DVD

servo board.

(1) From the bottom side of the DVD changer mechanism as-

sembly, remove the screw

attaching the switch board to

the DVD changer mechanism assembly.

(2) Loosen the screw

attaching the DVD traverse mecha-

nism assembly and take out the switch board while lifting
the section

of the DVD traverse mechanism assembly.

(3) Release the wires from the slots

of the switch board.

Reference:

When reassembling, pass the wire through the section

of the

DVD traverse mechanism assembly.

Fig.6

Fig.7

Fig.8

DVD pickup

DVD changer mechanism assembly

Short land sections

DVD changer mechanism assembly

DVD servo board

Card wire

CN451

CN452

CN453

Card wire

Wires

Switch board

DVD traverse mechanism assembly

CN201

Earth wire

DVD servo board

Lock

Card wire

CN101

Summary of Contents for UX-S77




















































































Search results

Summary of Contents for UX-S77

Reviews:

Related manuals for UX-S77

Brands by name

Popular brands

JVC UX-S77, Service Manual

Search results

Summary of Contents for UX-S77

Reviews:

Related manuals for UX-S77

Brands by name

Popular brands