Thank you for purchasing the JVC built-up adapter. Please carefully read these assembly and installation instructions before beginning
assembly.
Safety Precautions
Please read and understand these safety precautions before using this product.
Symbols
To highlight usage precautions and product depictions to assure safe and correct product usage and to avoid danger or injury to
persons using this product or other persons, several symbols are used.
Warning
Improper handling in disregard of these notices may result in bodily injury and even death.
Caution
Mishandling of the unit in disregard of these notices may result in bodily injury or damage to the unit.
Assembly/Installation Precautions
Warning
¶
Attaching this product to monitors other than those authorized by JVC may result in the monitor falling over or falling down,
potentially causing damage or bodily injury.
¶
Assemble all provided bolts, nuts and screws securely. Failure to do so may result in the monitor falling over or falling down,
potentially causing damage or bodily injury.
¶
Do not install in unstable locations such as uneven or sloped surfaces or locations subject to vibration or shock. Doing so may
result in the monitor falling over or falling down, potentially causing damage or bodily injury.
Caution
¶
To avoid against bodily injury or damage, be sure that you have sufficient working area before beginning assembly.
¶
Use this product only in a place where the temperature is between 5°C and 35°C. Failure to do so may cause damage to the monitor.
Parts List
Screw x 6
Please contact the store
where you purchased the
product if any parts are
missing.
Dimensions
unit:mm
Weight: 0.3 k
g
Assembly and Installation Instructions
BUILT-UP ADAPTER
TS-C9D2B
Installation Instructions
Monitor
Screw
Screw
LC35060-001A
© 2013 JVC KENWOOD Corporation
Tools required for assembly
Philips-head screwdriver
*Specifications and appearance of this unit are subject to change for improvement purposes without prior notice.
198
7
7
4.7
221.4
182.1
160
13
79.5
89.2
26.8
66.3
212.2
Caution
¶
To avoid injury to fingers, take care not to catch your finger between the monitor and the part when
tightening the parts together.
¶
Use the provided screws to fix the side panel.
1.
Adjust the stand height
to a lower position.
Refer to the monitor manual about how to
adjust the height of the stand.
2.
Attach the side panel to the monitor.
Set the side panel to the side of the monitor, then fix the left side and
right side panels with three screws each.
Side panel (Right)
Side panel (Left)
Guide hole
monitor
DT-V9L5
monitor
DT-V9L5
Guide pin
Belt loop
*Tightening torque of the screw:
0.8 - 1.0 N·m
Side panel (right)
x 1
Side panel (left)
x 1
Caution
¶
To avoid falling or dropping down of the monitors, take care of the following.
- Fix the monitors with a belt (not provided).
- You can stack up to two monitors. Do not stack three or more monitors.
- Do not stack the monitors with the batteries.
- Place the monitors in a horizontal position.
- Do not carry the monitors when they are stacked.
- Set the tilt angle of the monitor to 0° when you stack the monitors.
1.
Stack the monitors.
Set the guide hole to the guide pin on the left
and right side panels.
2.
Fix the stacked monitors with the belt.
Each side panel has a belt loop. Pull the belt(not provided) through the
belt loops at the top and the bottom, then fix the stacked monitors. Fix
both sides of the monitors with the belt.
*Use a belt less than 25mm in width, which is long enough to fit between
the belt loops in the illustration above, and strong enough to fix the
monitor.
Using the built-up adapter
Belt
(not provided)
190mm
TS-C9D2B̲JP̲EN.indd 4-5
TS-C9D2B̲JP̲EN.indd 4-5
2012/12/13 19:03:00
2012/12/13 19:03:00
