JVC RM-LP250M User Manual Download Page 13

Page: 13 / 21

Shift level via toggle

M8 Connection Status

Shows connection status. Button have no function

Iris

Displays Iris value

B9-B11

Iris range is used for calibrating the iris joystick to
match the maximums aperture open/closed
conditions for the lens. To calibrate:

Reset Points

Move joystick to fully open aperture and

set: Open

Move joystick to fully closed aperture and

set: Closed

LED Bar

Indicates Iris value

Joystick

Controls iris value

Ring

No function assigned to the joystick ring. The
camera protocol does not support setting an
absolute value for Master Black.

Button

Activates “Preview” relay on DB9 connector

B13

Shift: Off

Shift: On

Active Panel. If enabled
no hardware interface will
respond

Iris Range: Reset Points

B10

Iris one Push

Iris Range: Set fully
open

B11

Iris Mode. Light up Red
when in Auto. Green
when in manual

Iris Range: Set fully
closed

Shift: Off

Shift: On

B13

Upper Edge hold down:
Hijacks main display to
show actions for C1-C8

Lower Edge hold down:
Activates “Preview” relay
on DB9 connector

Sets Tally on camera via
Toggle

CONNECTED CAM STUDIO

C1 C2 C3 C4 C5 C6 C7 C8

ID Display

ID Tally

Black

B10

B11

B13

Iris

LED

Bar

- Joystick
- Ring
- Button

Position

Summary of Contents for RM-LP250M






















Search results

Summary of Contents for RM-LP250M

Reviews:

Related manuals for RM-LP250M

Brands by name

Popular brands

JVC RM-LP250M, User Manual

Search results

Summary of Contents for RM-LP250M

Reviews:

Related manuals for RM-LP250M

Brands by name

Popular brands