JVC LST1153-001A Instruction Manual Download Page 3

III

Safety Precautions

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

The exclamation point within an e

q

uilateral 

triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.

FOR USA AND CANADA

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK. 
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTSINSIDE.REFER 
SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, 
within an e

q

uilateral triangle is intended to 

alert the user to the presence of uninsulated 
“dangerous voltage” within the product’s 
enclosure that may be of sufficient magnitude 
to constitute a risk of electric shock to 
persons.

INFORMATION:

This e

q

uipment has been tested and found to comply 

with the limits for a Class A digital device, pursuant to 
Part 15 of the FCC Rules.
These limits are designed to provide reasonable 
protection against harmful interference when the 
e

q

uipment is operated in a commercial environment.

This e

q

uipment generates, uses, and can radiate 

radio fre

q

uency energy and, if not installed and used 

in accordance with the instruction manual, may cause 
harmful interference to radio communications. 
Operation of this e

q

uipment in a residential area is 

likely to cause harmful interference in which case the 
user will be re

q

uired to correct the interference at his 

own expense.

CAUTION:

CHANGES OR MODIFICATIONS NOT APPROVED 
BY JVC COULD VOID USER’S AUTHORITY TO 
OPERATE THE EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF THE 
FCC RULES. OPERATION IS SUBJECT TO THE 
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE 
MAY NOT CAUSE HARMFUL INTERFERENCE, AND 
(2) THIS DEVICE MUST ACCEPT ANY 
INTERFERENCE RECEIVED, INCLUDING 
INTERFERENCE THAT MAY CAUSE UNDESIRED 
OPERATION.

POUR CANADA

ATTENTION

Le symbole de l’éclair à l’intérieur d’un triangle 
é

q

uilatéral est destiné à alerter l’utilisateur sur la 

présence d’une “tension dangereuse” non isolée 
dans le boîtier du produit. Cette tension est 
suffisante pour provo

q

uer l’électrocution de 

personnes.

Le point d’exclamation à l’intérieur d’un triangle 
é

q

uilatéral est destiné à alerter l’utilisateur sur la 

présence d’opérations d’entretien importantes au 
sujet des

q

uelles des renseignements se trouvent 

dans le manuel d’instructions.

Ces symboles ne sont utilisés 

q

u’aux Etats-Unis.

RISQUE D’ELECTROCUTION 

NE PAS OUVRIR

ATT ENTION: 

POUR EVITER TOUT RISQUE D’ELECTROCUTION 
NE PAS OUVRIR LE BOITER. AUCUNE PIECE 
INTERIEURE N’EST A REGLER PAR L’UTILISATEUR. 
SE REFERER A UN AGENT QUALIFIE EN CAS DE 
PROBLEME.   

INFORMATION (FOR CANADA)
RENSEIGNEMENT (POUR CANADA) 

This Class A digital apparatus complies with Canadian 
ICES-003.

Cet appareil numéri

q

ue de la Class A est conforme à 

la norme NMB-003 du Canada.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, 
DO NOT EXPOSE THIS APPLIANCE TO RAINOR MOISTURE.

CAUTION:

This unit should be used with 120V AC only. (RM-HP7

9

0DU)

To prevent electric shocks and fire hazards, do NOT use 
anyother power source.

AVERTISSEMENT:

POUR EVITER LES RISQUES D’INCENDIE OU 
D’ELECTROCUTION, NE PAS EXPOSER L’APPAREIL 
A L’HUMIDITE OU A LA PLUIE.

 

ATTENTION:

Ce magnétoscope ne doit être utilisé 

q

ue sur du courant 

direct en 120V.
Afin d’eviter tout res

q

ue d’incendie ou d’electrocution, ne 

pas utillser d’autres sources d’alimentation électri

q

ue.

 

The apparatus shall not be exposed to dripping or 
splashing and that no objects filled with li

q

uids, such as 

vases, shall be placed close to the apparatus.

NOTE:

The rating plate and the safety caution are on the top of the unit.

REMARQUE:

La pla

q

ue d'identification (numéro de série) se trouve sur 

le panneau arrière de l'appareil.

 

CAUTION:

To prevent electric shock, do not open the cabinet.
No user serviceable parts inside. Refer servicing to 

q

ualified service personnel.

Due to design modifications, data given in this instruction 
book are subject to possible change without prior notice.

Summary of Contents for LST1153-001A













































Reviews: