JVC GY-HM150U, Instructions Manual

Page: 16 / 104

12
Introduction
A
LCD cover
B
[COMPONENT OUT] Component output terminal
(
A
Page 91)
C
[A/V OUT] Audio/Video output terminal (
A
Page 91)
D
[C.REVIEW/4] Clip Review/User 4 button (
A
Page 28)
For checking the most recently captured images.
You can also use it as a user button by assigning a specific
feature in the menu setting to this button. (
A
Page 19)
E
[ZEBRA/5] Zebra/User 5 button (
A
Page 32)
For displaying or canceling the display of zebra pattern
based on the luminance of the object. You can also use it as
a user button by assigning a specific feature in the menu
setting to this button. (
A
Page 19)
F
Built-in speaker (
A
Page 39)
Adjust the volume with the [ADJ./VOL.] knob on the rear.
Memo :
●
The built-in speaker is usable only in the Media mode. Audio
is not output from the built-in speaker during Camera mode.
●
Audio level in the Camera mode and Media mode can be
adjusted separately.
●
When in the Media mode, the volume of the headphone and
speaker are adjusted at the same time.
●
The built-in speaker cannot be used when the [HDMI]
terminal, [A/V OUT] terminal, or headphone jack is
connected.
G
[SLOT SEL] Slot selection button (
A
Page 25)
For switching the active card slot during shooting and
playback.
H
[LOLUX/3] Low-light shooting/User 3 button (
A
Page 19)
For switching the low-light shooting mode ON or OFF.
You can also use it as a user button by assigning a specific
feature in the menu setting to this button. (
A
Page 19)
I
[DISPLAY] Display button
For switching the displays on the LCD screen and viewfinder.
(
A
Page 20)
J
[REC] Record trigger button (
A
Page 27)
Button for starting or stopping recording.
K
LCD monitor (
A
Page 20)
L
[MENU/THUMB] Menu/Thumbnail button
The operation changes according to the status of the camera
recorder.
During Camera mode: Displays the menu screen. Press
again to exit the menu.
During Media mode: During media playback, the thumbnail
screen is displayed.
During thumbnail screen display, the thumbnail menu is
displayed.
M
Set lever
When in the Camera mode, this lever is used for Program AE
selection and as the zooming lever. (
A
Page 3 0)
When in the Media mode, this lever is used for clip selection
and playback control. (
A
Page 4 8 )
When the menu screen is displayed, this lever is used for
menu setting. (
A
Page 5 8 )
Bottom
N
Tripod mounting holes (
A
Page 15)
Memo :
●
To prevent the camera recorder from falling, attach
securely using the rotation prevention hole.
●
Use screws with screw length 5 mm and below.
Names of Parts (continued)
CH-2 INPUT
CH-1
3
45
2
1
23
0
CH-2
AUDIO INPUT
AUTO MANUAL
AUTO MANUAL
USER1
A B
FOCUS
ZOOM
ON
ND
FILTER
OFF
USER2
AF/MF FULL AUTO
AUDIO
SELECT
INPUT1
INPUT2
- LINE -
- MIC -
MIC+48V
INPUT1
INPUT2
GAIN
L-
M-
H-
B-
A-
PRST-
WHT.BAL IRI S A/M
C.REVIEW/4 ZEBRA/5
S LOT S EL
DISPLAY
COMPONENT
OUT
A / V OUT
LOLUX/3
MENU/
THUMB
T
W
REC
PR
OG
R
A
M
A
E
B
D
C
E
A
F G H I
J
K L M
N
LCD Monitor
When the LCD cover is opened
Bottom
GY-HM150U.book Page 12 Monday, September 5, 2011 1:48 AM