EN
47
TIMER RECORDING
You can programme this unit to timer record as many as
16 programmes.
If you do not know the
a
number for the programme you
wish to record, use the following procedure to set your unit to timer
record the programme.
1
Load a recordable disc if recording to DVD.
2
Press
PROGRAMME
to access the programme top screen.
3
Press
selection keys
to select
A
CALENDAR PR.
B
, then press
ENTER
.
●
When
A
PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES
B
appears on the TV screen, you need to
cancel some of the reserved programmes. (
A
pg. 48)
4
Press
selection keys
to select the desired date, then press
ENTER
.
5
Press
selection keys
to select
A
RECORD
TO
B
, then press
ENTER
. Press
selection keys
to
select the desired
recording deck, then
press
ENTER
.
6
Press
selection keys
to select
A
START
B
,
then press
ENTER
.
Press
selection keys
to set the desired start time, then press
ENTER
.
●
Each press of
F G
increases/decreases the start time in
1 minute interval.
●
To increase/decrease the start time in 30 minutes interval,
press and hold
F G
.
7
Press
selection keys
to select
A
STOP
B
, then press
ENTER
.
Press
selection keys
to set the desired stop time, then press
ENTER
.
●
Each press of
F G
increases/decreases the stop time in
1 minute interval.
●
To increase/decrease the stop time in 30 minutes interval, press
and hold
F G
.
8
Press
selection keys
to select
A
TV PROG
B
, then press
ENTER
. Press
selection keys
to select the desired channel.
9
Press
selection keys
to select
A
CONFIRM
B
, then press
ENTER
.
10
Set the other recording options as required.
●
Refer to step
8
in
A
c
Timer Programming
B
(
A
pg. 45).
11
Press
selection keys
to select
A
OK
B
, then
press
ENTER
to
access the
Programme
Confirmation screen.
12
Press
selection keys
to select
A
EXIT
B
, then
press
ENTER
to
complete timer
programming.
●
To programme another timer, press
selection keys
to select
A
CONTINUE
B
, then press
ENTER
.
●
If
A
PROGRAMME OVERLAPPED
B
appears on the TV
screen, delete or modify the programmes.
NOTES:
●
When two successive programmes are recorded on a DVD-RW
disc with Manual Timer Programming function, the beginning of
the second one may be left off the recording.
●
If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Manual Timer Programming
●
Make sure that the unit’s built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the AV mode.
●
Slide the
TV/CABLE/SAT/DVD
switch to
DVD
.
AUX
PROGRAMME
ENTER
FGDE
CABLE/SAT
DVD
TV
Selection Keys
BBC1
[MISC. ] XP
BBC1
23:00
22:30
HDD
[0]: SAT
2
PROGRAMME > CALENDAR PR. (2/3)
CONFIRM
14/01/04 WED 22:30 - 23:00
RECORD TO
STOP
START
TV PROG
ENTER
SELECT
PROGRAMME
EXIT
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
Satellite Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A
Perform
A
Satellite Receiver Control Setting
B
(
A
pg. 22).
B
Perform
A
Manual Timer Programming
B
(
A
pg. 47).
In step
8
, press
AUX
to change
A
TV PROG
B
to
A
SAT
B
. Then
press
selection keys
to enter the channel position for the
satellite broadcast.
C
Leave the satellite receiver’s power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in XP mode.
●
If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
●
If
A
JUST
B
is selected for the recording mode, the current
recording mode for the DVD deck is applied.
BBC1
1:00
28:00
2
PROGRAMME > CALENDAR PR. (3/3)
OK
INPUT TITLE
CATEGORY
VPS/PDC
WEEKLY/DAILY
REC MODE
GARDENING
EDUCATION
OFF
MON-FRI (FOR A WEEK)
FR360
14/01/04 WED 22:30 - 23:00
GARDENING
[EDUCATION] FR360
ENTER
SELECT
PROGRAMME
EXIT
PRESS [PROGRAMME]
TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
