background image

wiJAC2-002

 

Wireless Intercom System - Wireless Dropcord - N America

 

Operating Manual

 

Rev A

 

Page 9 

2.4 

Batteries (for both JB60 and JB69) 

W

ARNING:

 Charging battery types other than NiMH or NiCad may cause the batteries to leak or 

explode and cause damage or injury. If non-NiMH or non-NiCad batteries are installed, do not connect 

the Charging Port to a USB power source.  

The JB60-002 and JB69-002 each require three AA batteries. JAC recommends Duracell 800 mAh (or higher) NiMH 

or Duracell alkaline batteries for use in the 

wiJAC2

™ system to obtain the typical battery life. 

Removal of the batteries WILL NOT change any internal configuration of the unit. 

2.4.1 

Inserting or Replacing the Batteries 

Battery Lid Release 

To replace the batteries, remove the battery cover by unfastening the battery 

lid thumbscrew to release the upper end of the cover, and then gently lift the 

lid up and away from the body to release the two retaining tabs from the 

slots. 

Remove the batteries and insert new or fully charged batteries, matching the 

polarity marked on the battery holder.  

Retaining tabs 

2.4.2 

Charging Batteries in the Unit 

To charge rechargeable batteries in the unit, connect the Charging Port to a USB power source using the USB to 2.1 

mm male cable (CAB-USB-0013). If turned on during charging, the unit draws its power from the charging source, not 

the batteries, but battery charging will take longer. When charging is complete, the 'Full ' annunciator (

F

) will illuminate 

green. 

It should be possible to charge the unit via most USB power sources but this cannot be guaranteed for any products 

not made by or purchased from JAC.  

Note

:

 The batteries will charge whether theJB60/JB69 is switched on or switched off. Battery charging will take 

longer if the unit is switched on. 

2.4.3 

Charging Operation – via Battery Charger 

The batteries may be removed from the unit for charging in a separate battery charger. Removal of the batteries WILL 

NOT change any internal configuration of the unit.   

Note

: The JB60/JB69 will only charge the batteries when the internal temperature is within 0 to 40 °C 

Summary of Contents for JB60



















Reviews: