Juniper SRX4100 Hardware Manual Download Page 118

Page: 118 / 134

Grounded Equipment Warning

WARNING:

The services gateway is intended to be grounded. Ensure that

the services gateway is connected to earth ground during normal use.

Waarschuwing

Deze apparatuur hoort geaard te worden Zorg dat de

host-computer tijdens normaal gebruik met aarde is verbonden.

Varoitus

Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että

isäntälaite on yhdistetty maahan normaalikäytön aikana.

Attention

Cet équipement doit être relié à la terre. S'assurer que l'appareil

hôte est relié à la terre lors de l'utilisation normale.

Warnung

Dieses Gerät muß geerdet werden. Stellen Sie sicher, daß das

Host-Gerät während des normalen Betriebs an Erde gelegt ist.

Avvertenza

Questa apparecchiatura deve essere collegata a massa. Accertarsi

che il dispositivo host sia collegato alla massa di terra durante il normale
utilizzo.

Advarsel

Dette utstyret skal jordes. Forviss deg om vertsterminalen er jordet

ved normalt bruk.

Aviso

Este equipamento deverá estar ligado à terra. Certifique-se que o host

se encontra ligado à terra durante a sua utilização normal.

¡Atención!

Este equipo debe conectarse a tierra. Asegurarse de que el equipo

principal esté conectado a tierra durante el uso normal.

Varning!

Denna utrustning är avsedd att jordas. Se till att värdenheten är

jordad vid normal användning.

Backplane Energy Hazard Warning

WARNING:

High levels of electrical energy are distributed across the services

gateway backplane. Be careful not to contact the backplane connectors, or
any component connected to the backplane, with any metallic object while
servicing components installed in the services gateway.

Multiple Power Supplies Disconnection Warning

WARNING:

The services gateway has more than one power supply connection.

All connections must be removed completely to remove power from the unit
completely.

102

SRX4100 Services Gateway Hardware Guide

Summary of Contents for SRX4100


















































































































Search results

Summary of Contents for SRX4100

Reviews:

Brands by name

Popular brands

Juniper SRX4100, Hardware Manual

Search results

Summary of Contents for SRX4100

Reviews:

Brands by name

Popular brands