manualshive.com logo in svg

Juniper PTX5000, Hardware Manual

The Juniper PTX5000 is a high-performance networking device designed for large-scale data centers and service providers. To learn more about its features and specifications, you can download the free Hardware Manual from manualshive.com. This manual provides detailed instructions on how to operate and maintain your PTX5000.

Share
Download
background image

6.

Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to
one of the ESD points on the chassis.

7.

Remove the cover from the Routing Engine slots by loosening the captive screws on the corners of
the cover (using a number 2 Phillips (+) screwdriver).

CAUTION: Do not remove the cover if any of the LEDs are lit.

8.

Press the eject button on the right side of the CompactFlash card slot to release the CompactFlash
card.

9.

The CompactFlash card pops partially out of the slot. Grasp the card and pull it completely out of
the slot.

10. Place the CompactFlash card on the antistatic mat.

Figure 249: Removing a Routing Engine CompactFlash Card

Installing a CompactFlash Card in a PTX5000 Routing Engine

To install a CompactFlash card (see 

Figure 250 on page 471

):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to

one of the ESD points on the chassis.

2. Remove the cover from the Routing Engine slots by loosening the captive screws on the corners of

the cover (using a number 2 Phillips (+) screwdriver).

3. Insert the CompactFlash card into the CompactFlash card slot on the Routing Engine, with the logo

facing up.

CAUTION: Be sure to insert the CompactFlash card with the label facing up. Inserting
the CompactFlash card incorrectly might damage the Routing Engine.

4. Press the card firmly all the way into the slot.

470

Summary of Contents for PTX5000


















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PTX5000

ABB RELION REF615R Manual preview
RELION REF615R
Brand: ABB Pages: 66
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Brand: Tandberg Data Pages: 2
Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
IBM BladeCenter Management Module Installation And User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 184
B&B Electronics 232CC1A Product Information preview
232CC1A
Brand: B&B Electronics Pages: 2
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Brand: Ubiquiti Pages: 13
B&B Electronics EIR208 Series Quick Start Manual preview
EIR208 Series
Brand: B&B Electronics Pages: 2
StarTech.com ST1000SMPEX Instruction Manual preview
ST1000SMPEX
Brand: StarTech.com Pages: 9
Z-Com ZCN-1523H-5-16 Quick Installation Manual preview
ZCN-1523H-5-16
Brand: Z-Com Pages: 18
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
Supero SUPERSERVER 6027TR-H71FRF User Manual preview
SUPERSERVER 6027TR-H71FRF
Brand: Supero Pages: 118
Hamlet HRDSL512P4 Quick Start Manual preview
HRDSL512P4
Brand: Hamlet Pages: 11
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
Flexwatch FW3870 User Manual preview
FW3870
Brand: Flexwatch Pages: 13
BinTec BinGO! DSL II Quick Install Manual preview
BinGO! DSL II
Brand: BinTec Pages: 2
Calix GigaSpire BLAST u4hm Installation Manual preview
GigaSpire BLAST u4hm
Brand: Calix Pages: 45
TRENDnet TEG-PCITX User Manual preview
TEG-PCITX
Brand: TRENDnet Pages: 15
N-Tron 304TX-N Specifications preview
304TX-N
Brand: N-Tron Pages: 2

Brands by name

Popular brands

Load more brands